ATxmega256A3 Atmel Corporation, ATxmega256A3 Datasheet - Page 43
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATxmega256A3
Manufacturer Part Number
ATxmega256A3
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega256A3
Flash (kbytes)
256 Kbytes
Pin Count
64
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
50
Ext Interrupts
50
Usb Speed
No
Usb Interface
No
Spi
10
Twi (i2c)
2
Uart
7
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
2000
Analog Comparators
4
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
AES/DES
Sram (kbytes)
16
Eeprom (bytes)
4096
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
7
Output Compare Channels
22
Input Capture Channels
22
Pwm Channels
22
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATxmega256A3-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATxmega256A3-AUR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
ATxmega256A3B-MH
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATxmega256A3BU-AU
Manufacturer:
ST
Quantity:
12 000
Company:
Part Number:
ATxmega256A3BU-MH
Manufacturer:
AAT
Quantity:
400
Company:
Part Number:
ATxmega256A3U-AU
Manufacturer:
TI
Quantity:
12 000
Part Number:
ATxmega256A3U-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATxmega256A3U-MH
Manufacturer:
PANASONIC
Quantity:
1 450
26. DAC - 12-bit Digital to Analog Converter
26.1
26.2
8068T–AVR–12/10
Features
Overview
•
•
•
•
•
•
•
•
The XMEGA A3 features one two-channel, 12-bit, 1 Msps DACs with built-in offset and gain cal-
ibration, see
A DAC converts a digital value into an analog signal. The DAC may use an internal 1.0 voltage
as the upper limit for conversion, but it is also possible to use the supply voltage or any applied
voltage in-between. The external reference input is shared with the ADC reference input.
Figure 26-1. DAC overview
The DAC has one continuous output with high drive capabilities for both resistive and capacitive
loads. It is also possible to split the continuous time channel into two Sample and Hold (S/H)
channels, each with separate data conversion registers.
A DAC conversion may be started from the application software by writing the data conversion
registers. The DAC can also be configured to do conversions triggered by the Event System to
have regular timing, independent of the application software. DMA may be used for transferring
data from memory locations to DAC data registers.
The DAC has a built-in calibration system to reduce offset and gain error when loading with a
calibration value from software.
PORTB each has one DAC. Notation of this peripheral is DACB.
One DAC with 12-bit resolution
Up to 1 Msps conversion rate for each DAC
Flexible conversion range
Multiple trigger sources
1 continuous output or 2 Sample and Hold (S/H) outputs for each DAC
Built-in offset and gain calibration
High drive capabilities
Low Power Mode
Figure 26-1 on page
Channel A
Channel B
Register
Register
43.
Reference selection
Configuration
Trigger
DAC
Event
Channel A
Channel B
XMEGA A3
43