ATtiny261 Automotive Atmel Corporation, ATtiny261 Automotive Datasheet - Page 29
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATtiny261 Automotive
Manufacturer Part Number
ATtiny261 Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.ATTINY261_AUTOMOTIVE.pdf
(11 pages)
3.ATTINY261_AUTOMOTIVE.pdf
(16 pages)
4.ATTINY261_AUTOMOTIVE.pdf
(226 pages)
Specifications of ATtiny261 Automotive
Flash (kbytes)
2 Kbytes
Pin Count
20
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
4
Hardware Qtouch Acquisition
No
Max I/o Pins
16
Ext Interrupts
16
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
11
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
0.12
Eeprom (bytes)
128
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 150
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
No
Calibrated Rc Oscillator
Yes
- AT90CAN128_AUTOMOTIVE PDF datasheet
- ATTINY261_AUTOMOTIVE PDF datasheet #2
- ATTINY261_AUTOMOTIVE PDF datasheet #3
- ATTINY261_AUTOMOTIVE PDF datasheet #4
- Current page: 29 of 225
- Download datasheet (4Mb)
7.6
7.7
7701E–AVR–02/11
Calibrated Internal RC Oscillator
External Clock
By default, the Internal RC Oscillator provides an approximate 8MHz clock. Though voltage
and temperature dependent, this clock can be very accurately calibrated by the user. See
Table 22-2 on page 180
device is shipped with the CKDIV8 Fuse programmed. See
31
This clock may be selected as the system clock by programming the CKSEL Fuses as shown
in
loads the pre-programmed calibration value into the OSCCAL Register and thereby automati-
cally calibrates the RC Oscillator. The accuracy of this calibration is shown as Factory
calibration in
By changing the OSCCAL register from SW, see
on page
tion. The accuracy of this calibration is shown as User calibration in
When this Oscillator is used as the chip clock, the Watchdog Oscillator will still be used for the
Watchdog Timer and for the Reset Time-out. For more information on the pre-programmed
calibration value, see the section
Table 7-6.
Note:
When this Oscillator is selected, start-up times are determined by the SUT Fuses as shown in
Table 7-7 on page
Table 7-7.
Note:
To drive the device from an external clock source, CLKI should be driven as shown in
7-3 on page
grammed to “0000”.
SUT1..0
Table
for more details.
10
00
01
11
(1)
1. The device is shipped with this option selected.
1. The device is shipped with this option selected.
7-6. If selected, it will operate with no external components. During reset, hardware
32, it is possible to get higher calibration accuracy than by using the factory calibra-
Table 22-2 on page
CKSEL3..0
30. To run the device on an external clock, the CKSEL Fuses must be pro-
Internal Calibrated RC Oscillator Operating Modes
Start-up Times for the Internal Calibrated RC Oscillator Clock Selection
0010
from Power-down
29..
(1)
Start-up Time
6 CK
6 CK
6 CK
and
Atmel ATtiny24/44/84 [Preliminary]
“Internal Oscillator Speed” on page 204
“Calibration Byte” on page
180.
Additional Delay from
Reset (V
Reserved
14CK + 64 ms
14CK + 4 ms
“Oscillator Calibration Register – OSCCAL”
14CK
CC
Nominal Frequency
= 5.0V)
“System Clock Prescaler” on page
165.
8.0 MHz
Table 22-2 on page
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
for more details. The
Figure
180.
29
Related parts for ATtiny261 Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATTINY261-20MU](/photos/12/13/121309/313-32-qfn_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20MHZ 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY261-20PU](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20MHZ 20-DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY261-15MZ](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 2K FLASH 15MHZ 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY261-15MAZ](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 2KB FLASH 15MHZ 32-VQFN
Manufacturer:
Atmel
Datasheet:
![ATTINY261-20SU](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20MHZ 20SOIC
Manufacturer:
Atmel
Datasheet:
![ATtiny261](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![attiny261-20su-20s2](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Attiny261 8-bit Microcontroller With 2/4/8k Bytes In-system Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
![ATTINY261-20SUR](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20MHZ 20SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY261-20MUR](/photos/12/13/121309/313-32-qfn_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20MHZ 32QFN
Manufacturer:
Atmel
Datasheet: