ATtiny25 Automotive Atmel Corporation, ATtiny25 Automotive Datasheet - Page 108
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATtiny25 Automotive
Manufacturer Part Number
ATtiny25 Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.ATTINY25_AUTOMOTIVE.pdf
(7 pages)
3.ATTINY25_AUTOMOTIVE.pdf
(196 pages)
Specifications of ATtiny25 Automotive
Flash (kbytes)
2 Kbytes
Pin Count
8
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
4
Hardware Qtouch Acquisition
No
Max I/o Pins
6
Ext Interrupts
6
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
4
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
0.12
Eeprom (bytes)
128
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 125
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
5
Pwm Channels
6
32khz Rtc
No
Calibrated Rc Oscillator
Yes
- AT90CAN128_AUTOMOTIVE PDF datasheet
- ATTINY25_AUTOMOTIVE PDF datasheet #2
- ATTINY25_AUTOMOTIVE PDF datasheet #3
- Current page: 108 of 225
- Download datasheet (4Mb)
14.9.5
108
Atmel ATtiny24/44/84 [Preliminary]
Phase and Frequency Correct PWM Mode
The timer/counter overflow flag (TOV1) is set each time the counter reaches bottom. When
either OCR1A or ICR1 is used for defining the TOP value, the OC1A or ICF1 flag is set
accordingly on the same timer clock cycle on which the OCR1x registers are updated with the
double buffer value (at top). The interrupt flags can be used to generate an interrupt each time
the counter reaches the top or bottom value.
When changing the top value, the program must ensure that the new top value is higher or
equal to the value of all of the compare registers. If the top value is lower than any of the com-
pare registers, a compare match will never occur between TCNT1 and OCR1x. Note that
when using fixed top values, the unused bits are masked to zero when any of the OCR1x reg-
isters are written. As the third period shown in
the top actively while the timer/counter is running in the phase correct mode can result in an
asymmetrical output. The reason for this can be found in the time of update of the OCR1x reg-
ister. Since the OCR1x update occurs at top, the PWM period starts and ends at top. This
implies that the length of the falling slope is determined by the previous top value, while the
length of the rising slope is determined by the new top value. When these two values differ,
the two slopes of the period will differ in length. The difference in length gives the asymmetri-
cal result on the output.
It is recommended to use the phase and frequency correct mode instead of the phase correct
mode when changing the top value while the timer/counter is running. When using a static top
value, there are practically no differences between the two modes of operation.
In phase correct PWM mode, the compare units allow generation of PWM waveforms on the
OC1x pins. Setting the COM1x1:0 bits to two will produce a non-inverted PWM, and an
inverted PWM output can be generated by setting the COM1x1:0 to three (See
page
the port pin is set as output (DDR_OC1x). The PWM waveform is generated by setting (or
clearing) the OC1x register at the compare match between OCR1x and TCNT1 when the
counter increments, and clearing (or setting) the OC1x register at compare match between
OCR1x and TCNT1 when the counter decrements. The PWM frequency for the output when
using phase correct PWM can be calculated by the following equation:
The variable N represents the prescaler divider (1, 8, 64, 256, or 1024).
The extreme values for the OCR1x register represent special cases when generating a PWM
waveform output in the phase correct PWM mode. If the OCR1x is set equal to bottom, the
output will be continuously low, and if set equal to top, the output will be continuously high for
non-inverted PWM mode. For inverted PWM the output will have the opposite logic values.
The phase and frequency correct pulse width modulation, or phase and frequency correct
PWM, mode (WGM13:0 = 8 or 9) provides a high-resolution phase and frequency correct
PWM waveform generation option. The phase and frequency correct PWM mode is, like the
phase correct PWM mode, based on a dual-slope operation. The counter counts repeatedly
from bottom (0x0000) to top and then from top to bottom. In non-inverting compare output
mode, the output compare (OC1x) is cleared on the compare match between TCNT1 and
OCR1x while up-counting, and set on the compare match while down-counting.
114). The actual OC1x value will only be visible on the port pin if the data direction for
f
OCnxPCPWM
=
Figure 14-8 on page 107
---------------------------------
2
f
clk_I/O
N
TOP
illustrates, changing
Table 14-3 on
7701E–AVR–02/11
Related parts for ATtiny25 Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATTINY25-20MU](/photos/6/87/68751/313-20-qfn_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2K FLASH 20MHZ 20-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY25-20PU](/photos/6/50/65033/313-8-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 20MHZ 8-DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY25-20SU](/photos/6/50/65032/453-8-soic_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 20MHZ 8-SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY25-15MZ](/photos/30/99/309923/qfn-20_tmb.jpg)
Part Number:
Description:
MCU AVR 2K FLASH 15MHZ 20-QFN
Manufacturer:
Atmel
Datasheet:
![ATtiny25](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATTINY25-20MF](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
8-bit Microcontrollers - MCU AVR 16KB FL 512B EE 1KB SRAM 10 MHZ GRN
Manufacturer:
Atmel
![ATTINY25-20MFR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
8-bit Microcontrollers - MCU AVR 16KB FL 512B EE 1KB SRAM 10 MHZ GRN
Manufacturer:
Atmel
![ATTINY25-20SSU](/photos/6/50/65032/453-8-soic_tmb.jpg)
Part Number:
Description:
MCU AVR 2K ISP FLASH 2.7V 8-SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY25-20SSN](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 2KB FLASH 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY25-20SH](/photos/6/50/65032/453-8-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2KB FLASH 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY25-20SSH](/photos/6/50/65032/453-8-soic_tmb.jpg)
Part Number:
Description:
IC MCU AVR 2KB FLASH 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY25-20SSUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 2KB FLASH 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY25-20SUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 2KB FLASH 20MHZ 8SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY25-20MUR](/photos/6/87/68751/313-20-qfn_tmb.jpg)
Part Number:
Description:
MCU AVR 2KB FLASH 20MHZ 20QFN
Manufacturer:
Atmel
Datasheet: