ATtiny167 Automotive Atmel Corporation, ATtiny167 Automotive Datasheet - Page 149
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATtiny167 Automotive
Manufacturer Part Number
ATtiny167 Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.ATTINY167_AUTOMOTIVE.pdf
(10 pages)
3.ATTINY167_AUTOMOTIVE.pdf
(283 pages)
Specifications of ATtiny167 Automotive
Flash (kbytes)
16 Kbytes
Pin Count
20
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
8
Hardware Qtouch Acquisition
No
Max I/o Pins
16
Ext Interrupts
16
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Lin
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
11
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 150
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
3
Input Capture Channels
1
Pwm Channels
9
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
- AT90CAN128_AUTOMOTIVE PDF datasheet
- ATTINY167_AUTOMOTIVE PDF datasheet #2
- ATTINY167_AUTOMOTIVE PDF datasheet #3
- Current page: 149 of 225
- Download datasheet (4Mb)
18.10 Register Description
18.10.1
7701E–AVR–02/11
ADMUX – ADC Multiplexer Selection Register
To obtain best accuracy the coefficient k should be measured using two temperature calibra-
tions. Using offset calibration, set k = 1.0, where k = (1024*1.07mV/°C)/1.1V~1.0 [1/°C].
• Bit 7:6 – REFS1:REFS0: Reference Selection Bits
These bits select the voltage reference for the ADC, as shown in
these bits are changed during a conversion, the change will not go in effect until this
conversion is complete (ADIF in ADCSR is set).
Special care should be taken when changing differential channels. Once a differential channel
has been selected, the stage may take as much as 25 ADC clock cycles to stabilize to the new
value. Thus conversions should not be started within the first 13 clock cycles after selecting a
new differential channel. Alternatively, conversion results obtained within this period should be
discarded.
The same settling time should be observed for the first differential conversion after changing
ADC reference (by changing the REFS1:0 bits in the ADMUX register).
For channels where differential gain is used (i.e., the gain stage), using VCC or an optional
external AREF higher than (VCC - 1V) is not recommended, as this will affect ADC accuracy.
The internal voltage reference may not be connected to the AREF pin if an external voltage is
already being applied to it. The internal voltage reference is connected to the AREF pin when
REFS1:0 is set to the value "11".
Table 18-3.
• Bits 5:0 – MUX5:0: Analog Channel and Gain Selection Bits
The value of these bits selects which combination of analog inputs are connected to the ADC.
In the case of differential input, gain selection is also made with these bits. Selections on
18-4 on page 150
and the offset calibration selections are located. Selecting the single-ended channel ADC8
enables the temperature measurement. See
are changed during a conversion, the change will not go into effect until this conversion is
complete (ADIF in ADCSRA is set).
Bit
0x07 (0x27)
Read/Write
Initial Value
REFS1
0
0
1
1
Voltage Reference Selections for ADC
REFS1
REFS0
R/W
7
0
0
1
0
1
show values for single-ended channels and where the differential channels
REFS0
R/W
6
0
Voltage Reference Selection
V
External Voltage Reference at PA0 (AREF) pin, Internal Voltage Reference
turned off.
Internal 1.1V Voltage Reference.
Reserved.
Atmel ATtiny24/44/84 [Preliminary]
CC
used as analog reference, disconnected from PA0 (AREF).
MUX5
R/W
5
0
MUX4
R/W
4
0
Table 18-4 on page 150
MUX3
R/W
3
0
MUX2
R/W
2
0
Table 18-3 on page
MUX1
R/W
1
0
ffor details. If these bits
MUX0
R/W
0
0
ADMUX
149. If
Table
149
Related parts for ATtiny167 Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATTINY167-15MZ](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 16K FLASH 15MHZ 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY167-XU](/photos/39/70/397036/tssop20_tmb.jpg)
Part Number:
Description:
IC MCU AVR 16K FLASH 20TSSOP
Manufacturer:
Atmel
Datasheet:
![ATtiny167](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATTINY167-15MD](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 16K FLASH 15MHZ 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY167-15SZ](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
MCU AVR 16K FLASH 15MHZ 20-SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY167-15XD](/photos/6/80/68045/313-20-tssop_tmb.jpg)
Part Number:
Description:
MCU AVR 16K FLASH 15MHZ 20-TSSOP
Manufacturer:
Atmel
Datasheet:
![ATTINY167-15XZ](/photos/6/80/68045/313-20-tssop_tmb.jpg)
Part Number:
Description:
MCU AVR 16K FLASH 15MHZ 20-TSSOP
Manufacturer:
Atmel
Datasheet:
![ATTINY167-SU](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC MCU AVR 16K FLASH 20SOIC
Manufacturer:
Atmel
Datasheet: