ATmega6490A Atmel Corporation, ATmega6490A Datasheet - Page 17

• Manufacturer Part Number: ATmega6490A
• Manufacturer: Atmel Corporation

Specifications of ATmega6490A

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 160
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

7.6.1
7.7
8284D–AVR–6/11
Instruction Execution Timing
SPH and SPL – Stack pointer High and Stack Pointer Low
ATmega169A/PA/329A/PA/3290A/PA/649A/P/6490A/P
Note:
This section describes the general access timing concepts for instruction execution. The AVR
CPU is driven by the CPU clock clk
chip. No internal clock division is used.
Figure 7-4
vard architecture and the fast-access Register File concept. This is the basic pipelining concept
to obtain up to 1 MIPS per MHz with the corresponding unique results for functions per cost,
functions per clocks, and functions per power-unit.
Figure 7-4.
Figure 7-5
operation using two register operands is executed, and the result is stored back to the destina-
tion register.
Figure 7-5.
Bit
0x3E (0x5E)
0x3D (0x5D)
Read/Write
Initial Value
Register Operands Fetch
2nd Instruction Execute
3rd Instruction Execute
1st Instruction Execute
ALU Operation Execute
2nd Instruction Fetch
1. Reserved bits in ATmega169A/169PA
3rd Instruction Fetch
4th Instruction Fetch
1st Instruction Fetch
Total Execution Time
shows the internal timing concept for the Register File. In a single clock cycle an ALU
shows the parallel instruction fetches and instruction executions enabled by the Har-
Result Write Back
The Parallel Instruction Fetches and Instruction Executions
Single Cycle ALU Operation
SP15
R/W
R/W
SP7
15
7
0
0
(1)
clk
clk
CPU
CPU
SP14
R/W
R/W
SP6
14
6
0
0
(1)
SP13
R/W
R/W
SP5
CPU
13
5
0
0
T1
T1
(1)
, directly generated from the selected clock source for the
SP12
R/W
R/W
SP4
12
4
0
0
(1)
SP11
T2
R/W
R/W
SP3
T2
11
3
0
0
(1)
SP10
SP2
R/W
R/W
10
2
0
0
T3
T3
SP9
SP1
R/W
R/W
9
1
0
0
SP8
SP0
R/W
R/W
8
0
0
0
T4
T4
SPH
SPL
17