ATmega32U4 Atmel Corporation, ATmega32U4 Datasheet - Page 20

• Manufacturer Part Number: ATmega32U4
• Manufacturer: Atmel Corporation

Specifications of ATmega32U4

• Flash (kbytes): 32 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 14
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 26
• Ext Interrupts: 13
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 3.3
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 2
• Pwm Channels: 8
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

8. Errata
8.1
8.2
7766FS–AVR–11/10
ATmega16U4/ATmega32U4 Rev E
ATmega16U4/ATmega32U4 Rev D
The revision letter in this section refers to the revision of the ATmega16U4/ATmega32U4
device.
•
•
•
1. Spike on TWI pins when TWI is enabled
2. High current consumption in sleep mode
3. MSB of OCR4A/B/D is write only in 11-bits enhanced PWM mode
•
•
•
1. Spike on TWI pins when TWI is enabled
2. High current consumption in sleep mode
Spike on TWI pins when TWI is enabled
High current consumption in sleep mode
MSB of OCR4A/B/D is write only in 11-bits enhanced PWM mode
Spike on TWI pins when TWI is enabled
High current consumption in sleep mode
Timer 4 11-bits enhanced PWM mode
100 ns negative spike occurs on SDA and SCL pins when TWI is enabled.
Problem Fix/work around
Enable ATmega16U4/ATmega32U4 TWI before the other nodes of the TWI network.
If a pending interrupt cannot wake the part up from the selected mode, the current consump-
tion will increase during sleep when executing the SLEEP instruction directly after a SEI
instruction.
Problem Fix/work around
Before entering sleep, interrupts not used to wake up the part from the sleep mode should
be disabled.
In the 11-bits enhanced PWM mode the MSB of OCR4A/B/D is write only. A read of
OCR4A/B/D will always return zero in the MSB position.
Problem Fix/work around
None.
100 ns negative spike occurs on SDA and SCL pins when TWI is enabled.
Problem Fix/work around
Enable ATmega16U4/ATmega32U4 TWI before the other nodes of the TWI network.
If a pending interrupt cannot wake the part up from the selected mode, the current consump-
tion will increase during sleep when executing the SLEEP instruction directly after a SEI
instruction.
Problem Fix/work around
Before entering sleep, interrupts not used to wake up the part from the sleep mode should
be disabled.
ATmega16/32U4
20