ATmega16HVA Atmel Corporation, ATmega16HVA Datasheet - Page 4

• Manufacturer Part Number: ATmega16HVA
• Manufacturer: Atmel Corporation

Specifications of ATmega16HVA

• Flash (kbytes): 16 Kbytes
• Pin Count: 28
• Max. Operating Frequency: 4 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 3
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 6
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 6
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1.9
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 256
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -20 to 85
• I/o Supply Class: 1.8 to 9.0
• Operating Voltage (vcc): 1.8 to 9.0
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 4
• Input Capture Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

1.3.7
1.3.8
1.3.9
1.3.10
1.3.11
1.3.12
1.3.13
1.3.14
1.3.15
1.3.16
1.3.17
4
ATmega8HVA/16HVA
GND
Port A (PA1..PA0)
Port B (PB3..PB0)
PC0
OC
OD
NI
PI
NV/PV1/PV2
BATT
RESET/dw
Ground
Port A serves as a low-voltage 2-bit bi-directional I/O port with internal pull-up resistors (selected
for each bit). As inputs, Port A pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port A pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port A also serves the functions of various special features of the ATmega8HVA/16HVA as
listed in
Port B is a low-voltage 4-bit bi-directional I/O port with internal pull-up resistors (selected for
each bit). As inputs, Port B pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port B pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port B also serves the functions of various special features of the ATmega8HVA/16HVA as
listed in
Port C serves the functions of various special features of the ATmega8HVA/16HVA as listed in
”Alternate Functions of Port C” on page
High voltage output to drive Charge FET.
High voltage output to drive Discharge FET.
NI is the filtered negative input from the current sense resistor.
PI is the filtered positive input from the current sense resistor.
NV, PV1, and PV2 are the inputs for battery cells 1 and 2.
Input for detecting when a charger is connected.
Reset input. A low level on this pin for longer than the minimum pulse length will generate a
reset, even if the clock is not running. The minimum pulse length is given in Table 11 on page
38. Shorter pulses are not guaranteed to generate a reset. This pin is also used as debugWIRE
communication pin.
”Alternate Functions of Port A” on page
”Alternate Functions of Port B” on page
61.
70.
71.
8024AS–AVR–04/08