ATmega1284RZAP Atmel Corporation, ATmega1284RZAP Datasheet - Page 285
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega1284RZAP
Manufacturer Part Number
ATmega1284RZAP
Description
Manufacturer
Atmel Corporation
Specifications of ATmega1284RZAP
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
No
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
0.25
Antenna Diversity
No
External Pa Control
No
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
16.0
Transmit Current Consumption (ma)
17.0
Link Budget (dbm)
104
- Current page: 285 of 380
- Download datasheet (7Mb)
24.8.11
24.8.12
8059D–AVR–11/09
Preventing Flash Corruption
Programming Time for Flash when Using SPM
instruction is executed within three CPU cycles. When SIGRD and SPMEN are cleared, LPM will
work as described in the Instruction set Manual.
Table 24-5.
Note:
During periods of low V
too low for the CPU and the Flash to operate properly. These issues are the same as for board
level systems using the Flash, and the same design solutions should be applied.
A Flash program corruption can be caused by two situations when the voltage is too low. First, a
regular write sequence to the Flash requires a minimum voltage to operate correctly. Secondly,
the CPU itself can execute instructions incorrectly, if the supply voltage for executing instructions
is too low.
Flash corruption can easily be avoided by following these design recommendations (one is
sufficient):
1. If there is no need for a Boot Loader update in the system, program the Boot Loader Lock
2. Keep the AVR RESET active (low) during periods of insufficient power supply voltage.
3. Keep the AVR core in Power-down sleep mode during periods of low V
The calibrated RC Oscillator is used to time Flash accesses.
typical programming time for Flash accesses from the CPU.
Table 24-6.
Note:
Signature Byte
Device Signature Byte 1
Device Signature Byte 2
Device Signature Byte 3
RC Oscillator Calibration Byte
Flash write (Page Erase, Page Write, and
write Lock bits by SPM)
bits to prevent any Boot Loader software updates.
This can be done by enabling the internal Brown-out Detector (BOD) if the operating volt-
age matches the detection level. If not, an external low V
used. If a reset occurs while a write operation is in progress, the write operation will be
completed provided that the power supply voltage is sufficient.
vent the CPU from attempting to decode and execute instructions, effectively protecting
the SPMCSR Register and thus the Flash from unintentional writes.
All other addresses are reserved for future use.
1. Minimum and maximum programming times is per individual operation.
Signature Row Addressing
SPM Programming Time
Symbol
CC
, the Flash program can be corrupted because the supply voltage is
(1)
Min Programming Time
Z-Pointer Address
0x0000
0x0002
0x0004
0x0001
3.7 ms
CC
Table 24-6 on page 285
reset protection circuit can be
ATmega1284P
Max Programming Time
CC
. This will pre-
4.5 ms
shows the
285
Related parts for ATmega1284RZAP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATMEGA128](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA128-8AC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA128-8AI](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA128RFA1-ZU](/photos/12/13/121326/313-64-qfn_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA328P-20PU](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
![ATMEGA64RZAV-10PU](/photos/14/18/141872/atmega64rzav-10pu_tmb.jpg)
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA64RZAPV-10MU](/photos/12/13/121326/313-64-qfn_tmb.jpg)
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA64RZAPV-10AU](/photos/6/70/67042/313-44-tqfp_tmb.jpg)
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA128RZAV-8AU](/photos/12/13/121332/313-64-tqfp_tmb.jpg)
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA168PA-PU](/photos/19/6/190669/ge28pdip05-40_tmb.jpg)
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
![MIKROE-459](/photos/40/80/408077/mcu_card_atmega_tmb.jpg)
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika