AT32UC3L0128 Atmel Corporation, AT32UC3L0128 Datasheet - Page 26

• Manufacturer Part Number: AT32UC3L0128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3L0128

• Flash (kbytes): 128 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Speed: No
• Usb Interface: No
• Spi: 5
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

5.1.4
5.1.4.1
5.1.4.2
5.2
5.2.1
5.2.2
32145AS–12/2011
Startup Considerations
Power-up Sequence
Starting of Clocks
Fetching of Initial Instructions
Maximum Rise Rate
Minimum Rise Rate
To avoid risk of latch-up, the rise rate of the power supplies must not exceed the values
described in
Recommended order for power supplies is also described in this chapter.
The integrated Power-on Reset (POR33) circuitry monitoring the VDDIN powering supply
requires a minimum rise rate for the VDDIN power supply.
See
If the application can not ensure that the minimum rise rate condition for the VDDIN power sup-
ply is met, one of the following configurations can be used:
This chapter summarizes the boot sequence of the AT32UC3L0128/256. The behavior after
power-up is controlled by the Power Manager. For specific details, refer to the Power Manager
chapter.
After power-up, the device will be held in a reset state by the Power-on Reset (POR18 and
POR33) circuitry for a short time to allow the power to stabilize throughout the device. After
reset, the device will use the System RC Oscillator (RCSYS) as clock source. Please refer to
Table 7-17 on page 43
On system start-up, the DFLL is disabled. All clocks to all modules are running. No clocks have
a divided frequency; all parts of the system receive a clock with the same frequency as the Sys-
tem RC Oscillator.
When powering up the device, there may be a delay before the voltage has stabilized, depend-
ing on the rise time of the supply used. The CPU can start executing code as soon as the supply
is above the POR18 and POR33 thresholds, and before the supply is stable. Before switching to
a high-speed clock source, the user should use the BOD to make sure the VDDCORE is above
the minimum level (1.62V).
After reset has been released, the AVR32 UC CPU starts fetching instructions from the reset
address, which is 0x80000000. This address points to the first address in the internal Flash.
The code read from the internal flash is free to configure the clock system and clock sources.
Please refer to the PM and SCIF chapters for more details.
• A logic “0” value is applied during power-up on pin PA11 until VDDIN rises above 1.2V.
• A logic “0” value is applied during power-up on pin RESET_N until VDDIN rises above 1.2V.
Table 7-3 on page 31
Table 7-3 on page
for the frequency for this oscillator.
for the minimum rise rate value.
31.
AT32UC3L0128/256
26