AT32UC3A1512AU Atmel Corporation, AT32UC3A1512AU Datasheet - Page 7

• Manufacturer Part Number: AT32UC3A1512AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1512AU

• Flash (kbytes): 512 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

7745C–AVR32–05/09
Note that the general-purpose fuse bits 29 to 31 are meaningless for the MCU hardware. They
are only interpreted by the bootloader and can be freely used by the application if the bootloader
is removed.
Table 6-2. Bootloader Area Specified by BOOTPROT
Table 6-3. BOD Activation Settings
The general-purpose fuse bits can be changed in one of the following ways:
•
•
•
BOOTPROT
7
6
5
4
3
2
1
0
ISP_BOD_EN
GP 29
0
x
0
0
1
With JTAGICE mkII, use the
writefuses
Studio.
With ISP, use the
‘Program Fuses...’ on the appropriate ISP AVR32 target in AVR32 Studio (see Section
7.5.2).
From the running embedded application, use the WGPB, EGPB, PGPFB and EAGPF
FLASHC commands. See the AVR UC3 datasheets referred to by Section 3 for further
information and take care of the Lock errors that can occur with these commands.
), or execute ‘Program Fuses...’ on the JTAGICE mkII AVR32 target in AVR32
Pages
Protected
by
BOOTPROT
None
0-1
0-3
0-7
0-15
0-31
0-63
0-127
BODEN
GP 28
0
0
1
1
x
except 01b
CONFIGURATION
GP 27
0
1
0
1
x
1024 bytes
2048 bytes
4096 bytes
8192 bytes (default value used by the bootloader)
16384 bytes
32768 bytes
65536 bytes
Size of Protected Memory
0 byte
avr32program writefuses
Description
BOD disabled.
BOD enabled by hardware, BOD reset enabled.
DO NOT USE WITH THE ISP OR THE BOOT PROCESS
WILL BEHAVE ABNORMALLY BECAUSE OF
CORRUPTED RESET CAUSES.
BOD enabled by hardware, BOD reset replaced by BOD
interrupt.
BOD disabled.
BOD enabled with reset by the ISP using the BODLEVEL
and BODHYST settings from the GP fuses.
memory with BatchISP (see Section 7.4.2), or execute
command (see
avr32program help
7