HA4600CPZ Intersil, HA4600CPZ Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
HA4600CPZ
Manufacturer Part Number
HA4600CPZ
Description
IC VIDEO BUFFER 480MHZ 8-DIP
Manufacturer
Intersil
Datasheet
1.HA4600CBZ.pdf
(7 pages)
Specifications of HA4600CPZ
Applications
Buffer
Number Of Circuits
1
-3db Bandwidth
480MHz
Slew Rate
1770 V/µs
Current - Supply
10.5mA
Current - Output / Channel
20mA
Voltage - Supply, Single/dual (±)
±4.5 V ~ 5.5 V
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Application Information
General
The HA4600 is a unity gain buffer that is optimized for high
performance video applications. The output disable function
makes it ideal for the matrix element in small, high input-to-
output isolation switchers and routers. This buffer contains no
feedback or gain setting resistors, so the output is a true high
impedance load when the IC is disabled (EN = 0). The HA4600
also excels as an input buffer for routers with a large number of
outputs (i.e. each input must connect to a large number of
outputs) and delivers performance superior to most video
amplifiers at a fraction of the cost. As an input buffer, the
HA4600’s low input capacitance and high input resistance
provide excellent video terminations when used with an
external 75Ω resistor.
Frequency Response
Most applications utilizing the HA4600 require a series
output resistor, R
capacitance, C
as C
table), so give careful consideration to component
placement to minimize trace length. As an example, -3dB
bandwidth decreases to 160MHz for C
In big matrix configurations where C
frequency response is obtained by cascading two levels of
crosspoints in the case of multiplexed outputs (see Figure
2), or distributing the load between two drivers if C
bussing and subsequent stage input capacitance.
Control Signals
EN - The ENABLE input is a TTL/CMOS compatible, active
high input. When driven low this input forces the output to a
true high impedance state and reduces the power
dissipation by two orders of magnitude. The EN input has no
on-chip pull-up resistor, so it must be connected to a logic
high (recommend V+) if the enable function isn’t utilized.
Switcher/Router Applications
Figure 1 illustrates one possible implementation of a
wideband, low power, 4 x 4 switcher/router. A 4 x 4
switcher/router allows any of the four outputs to be driven by
any one of the four inputs (e.g. each of the four inputs may
connect to a different output, or an input may connect to
multiple outputs). This application utilizes the HA4600 for the
input buffer, the HA4404 (4 x 1 crosspoint switch) as the
switch matrix, and the HFA1112 (programmable gain buffer)
as the gain of two output driver. Figure 2 details a 16 x 1
switcher (basically a 16:1 MUX) which uses the HA4600 in a
cascaded stage configuration to minimize capacitive loading
at each output node, thus increasing system bandwidth.
Power Up Considerations
No signals should be applied to the analog or digital inputs
before the power supplies are activated. Latch-up may occur
if the inputs are driven at the time of power up. To prevent
L
increases (as shown in the Electrical Specification
L
, driven. Bandwidth and slew rate degrade
S
, to tune the response for the specific load
4
L
is large, better
L
= 100pF, R
L
is due to
S
= 0Ω.
HA4600
latch-up, the input currents during power up must not exceed
the values listed in the Absolute Maximum Ratings.
Intersil’s Crosspoint Family
Intersil offers a variety of 1 x 1 and 4 x 1 crosspoint switches. In
addition to the HA4600, the 1 x 1 family includes the HA4201
which is an essentially similar device that includes a Tally
output (enable indicator). The 4 x 1 family is comprised of the
HA4314, HA4404, and HA4344. The HA4314 is a 14 lead basic
4 x 1 crosspoint. The HA4404 is a 16 lead device with Tally
outputs to indicate the selected channel. The HA4344 is a 16
lead crosspoint with synchronized control lines (A0, A1, CS).
With synchronization, the control information for the next
channel switch can be loaded into the crosspoint without
affecting the current state. On a subsequent clock edge the
stored control state effects the desired channel switch.
December 22, 2005
FN3990.8