L6232E SGS-Thomson-Microelectronics, L6232E Datasheet
L6232E
Available stocks
Related parts for L6232E
L6232E Summary of contents
Page 1
... All necessary circuitry to perform PWM and linear motor speed control is included. A central charge pump is util- ized to drive the upper DMOS transistors, and also to power the braking function. The L6232E is packaged in PLCC28. 1/10 ...
Page 2
... L6232E PIN DESCRIPTION Pin Name GND Common Ground. Also provides heat-sink to PCB SENSE Output for current sense resistors. 6 INLB Logic Input to turn on the lower driver (Active High Supply Voltage INLA Logic input to turn on the lowey driver (Active High). ...
Page 3
... DS See Fig note1 LIN V = 0.4 to 5.5V ref PWM V = 0.4 to 5.5V ref Note 0 (PWM motor I (LIN) = 200mA motor PWM V = 2.5V, ref LIN V = 0.4V, ref R = 0.5 ; Note 2 S L6232E Value Unit -0 -0 3.5 A 1.8 A 1.5 W -40 to 150 C Value Unit Max ...
Page 4
... L6232E ELECTRICAL CHARACTERISTICS (continued) Symbol Parameter G LIN Error Amplifier m Transconductance Zout Error Amplifier Output Impedance V Logic Input Voltage BRK; INUA; INH INUB; INUC; INLA; INLB; INLC V INL I Logic Input Current BRK; INUA; INH(leak) INUB; INUC; INLA; INLB; INLC I INL t Upper/Lower Turn-on Delay ...
Page 5
... Figure 1: Brake Delay and Braking timing of the L6232E. At the time Powerdown threshold detector drives low the BRK input; at time t2 the Charge Pump voltage becomes inadequate to maintain ON the lower DMOS. FUNCTIONAL DESCRIPTION (Refer to the Block Diagram) The commutation sequence is provided by the user via six inputs ...
Page 6
... C3 must be chosen of adeguate quality (very high equivalent parallel resistance). C4 can be a ceramic disk capacitor . The typical applica- tion od the L6232E is in HDD systems on which there is the need to park the Read-Write Heads be- fore the motor braking. This behavior is possible with the circuit of Fig.3. At Power Supply switch-off (see Fig ...
Page 7
... Care must be taken in the PC Board design particularly about ground loops and ground cop- per area. The typical Thermal Resistance junction to ambient versus PC Board copper area (Fig.7) is shown in Fig 8. For Transient Thermal Resis- tance see Fig. 9. vs. Figure 5: Output Voltage Slew Rate Control vs. 1/R Value 2 L6232E 7/10 ...
Page 8
... L6232E Figure 6: Typical Body Diode Forward Drop vs. Drain to Source Current. Figure 8: Typical R vs. On-Board Heatsink th j-amb Side l. 8/10 Figure 7: On Board Dissipation Copper Area Size Figure 9: Typical Transient R in Single Pulse th Condition. ...
Page 9
... PLCC28 PACKAGE MECHANICAL DATA DIM. MIN. TYP. A 12.32 B 11.43 D 4.2 D1 2.29 D2 0.51 E 9.91 e 1.27 e3 7.62 F 0. 1.24 M1 1.143 mm MAX. MIN. 12.57 0.485 11.58 0.450 4.57 0.165 3.04 0.090 0.020 10.92 0.390 0.101 L6232E inch TYP. MAX. 0.495 0.456 0.180 0.120 0.430 0.050 0.300 0.018 0.028 0.004 0.049 0.045 9/10 ...
Page 10
... L6232E Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned in this publication are subject to change without notice ...