ETC5067N SGS-Thomson-Microelectronics, ETC5067N Datasheet
ETC5067N
Available stocks
Related parts for ETC5067N
ETC5067N Summary of contents
Page 1
... Also included is an Analog Loopback switch and TS output. X November 1994 ETC5064/64-X ETC5067/67-X POWER AMPLIFIER DIP20 (Plastic) N ORDERING NUMBERS: ETC5064N ETC5064N-X ETC5067N ETC5067N-X PL CC20 ORDERING NUMBERS: ETC5064FN ETC5064FN-X ETC5067FN ETC5067FN ORDERING NUMBERS: 6.6 V ETC5064D ETC5064D-X ETC5067D ETC5067D 1/18 ...
Page 2
ETC5064 - ETC5064-X - ETC5067 - ETC5067-X PIN CONNECTIONS (Top views) DIP20 & SO20 BLOCK DIAGRAM (ETC5064 - ETC5064-X - ETC5067 - ETC5067-X) 2/18 PLCC20 ...
Page 3
PIN DESCRIPTION Pi n Name N Type (*) + VPO O 1 GNDA GND 2 - VPO O 3 VPI BCLK ...
Page 4
ETC5064 - ETC5064-X - ETC5067 - ETC5067-X FUNCTIONAL DESCRIPTION POWER-UP When power is first applied, power-on reset circuitry initializes the device and places it into the power- down mode. All non-essential circuits are deacti- vated and the D and VF ...
Page 5
For 64 kHz operation, the frame sync pulses must be kept low for a minimum of 160 ns (see Fig 1). The D TRI-STATE output X buffer is enabled with the rising edge of FS rising ...
Page 6
ETC5064 - ETC5064-X - ETC5067 - ETC5067-X ELECTRICAL OPERATING CHARACTERISTICS V = 5.0V 5 -5V 5%, GNDA = 0V otherwise noted; typical characteristics specified at V enced to GNDA. DIGITAL INTERFACE (All devices) Symbol V ...
Page 7
ELECTRICAL OPERATING CHARACTERISTICS (Continued) ANALOG INTERFACE WITH POWER AMPLIFIERS (all devices) Symbol IPI Input Leakage Current (– 1.0 V RIPI Input Resistance (– 1.0 VIOS Input Offset Voltage ROP Output Resistance (inverting unity–gain at VPO F Unity–gain Bandwidth, Open Loop ...
Page 8
ETC5064 - ETC5064-X - ETC5067 - ETC5067-X All TIMING SPECIFICATIONS Symbol 1/t Frequency of master clocks PM MCLK and MCLK X R Depends on the device used and the BCLK /CLKSEL Pin R t Width of Master Clock High WMH ...
Page 9
Figure 2 : Short Frame Sync Timing. ETC5064 - ETC5064-X - ETC5067 - ETC5067-X 9/18 ...
Page 10
ETC5064 - ETC5064-X - ETC5067 - ETC5067-X Figure 3 : Long Frame Sync Timing. 10/18 ...
Page 11
TRANSMISSION CHARACTERISTICS (all devices (ETC5064-X/67- GNDA = 0V 1.02kHz 0dBm0 transmit input amplifier connected forunity–gainnon–inverting.(unless IN otherwise specified). AMPLITUDE RESPONSE Symbo l Absolute Levels - Nominal 0 ...
Page 12
ETC5064 - ETC5064-X - ETC5067 - ETC5067-X TRANSMISSION CHARACTERISTICS (continued). ENVELOPE DELAY DISTORTION WITH FREQUENCY Symbol D Transmit Delay, Absolute (f = 1600 Hz Transmit Delay, Relative 500 Hz-600 600 ...
Page 13
TRANSMISSION CHARACTERISTICS (continued). DISTORTION Symbol STD Signal to Total Distortion (sinusoidal test method STD Transmit or Receive Half-channel R Level = 3.0 dBm0 = 0 dBm0 to – 30 dBm0 = – 40 dBm0 = – 55 dBm0 ...
Page 14
ETC5064 - ETC5064-X - ETC5067 - ETC5067-X APPLICATION INFORMATION POWER SUPPLIES While the pins at the ETC506X family are well pro- tected against electrical misure recommended that the standard CMOS practice be followed, en- suring that ground is ...
Page 15
SO20 PACKAGE MECHANICAL DATA DIM. MIN 0 0. 7 ETC5064 - ETC5064-X - ETC5067 - ETC5067-X mm TYP. MAX. MIN. 2.65 ...
Page 16
ETC5064 - ETC5064-X - ETC5067 - ETC5067-X PLCC20 PACKAGE MECHANICAL DATA DIM. MIN. A 9.78 B 8. 16/18 mm TYP. MAX. MIN. 10.03 0.385 9.04 0.350 4.57 0.165 ...
Page 17
DIP20 PACKAGE MECHANICAL DATA DIM. MIN. a1 0.254 B 1. ETC5064 - ETC5064-X - ETC5067 - ETC5067-X mm TYP. MAX. MIN. 0.010 1.65 0.055 0.45 0.25 25.4 8.5 2.54 22.86 ...
Page 18
ETC5064 - ETC5064-X - ETC5067 - ETC5067-X Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of ...