HCPL-7820 Agilent Technologies, Inc., HCPL-7820 Datasheet
HCPL-7820
Available stocks
Related parts for HCPL-7820
HCPL-7820 Summary of contents
Page 1
... When used with a shunt resistor in the current path, the HCPL-7820/7825 provides a cost-effective, auto-insertion compatible current sense solution. Fast propagation delays allow this part to be used in either motor drive or inverter applications for ...
Page 2
... This performance is delivered in an auto-insertable, industry standard Ordering Information HCPL-782x Option yyy 300 = Gull Wing Surface Mount Lead Option 500 = Tape/Reel Package Option (1 k min.) Option datasheets available. Contact your Hewlett-Packard sales representative or authorized distributor for information ...
Page 3
Gull Wing Surface Mount Option 300* 9.65 ± 0.25 (0.380 ± 0.010 7820 YYWW 1 2 MOLDED 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2.540 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). TOLERANCES (UNLESS OTHERWISE SPECIFIED): ...
Page 4
... Regulatory Information The HCPL-7820/7825 has been approved by the following organizations: UL Recognized under UL 1577, Component Recognition Program, FILE E55361. Insulation and Safety Related Specifications Parameter Symbol Min. External Air Gap L(IO1) (External Clearance) Min. External Tracking Path L(IO2) (External Creepage) Min. Internal Plastic Gap ...
Page 5
Absolute Maximum Ratings Parameter Storage Temperature Ambient Operating Temperature Supply Voltages Steady-State Input Voltage Two Second Transient Input Voltage Output Voltages Lead Solder Temperature (1.6 mm below seating plane, 10 sec.) Reflow Temperature Profile Recommended Operating Conditions Parameter Ambient Operating ...
Page 6
... V and unless otherwise noted. DD1 DD2 Parameter Symbol Input Offset Voltage V OS Absolute Value of Input | Offset Change vs. Temperature Gain: HCPL-7820 G Gain: HCPL-7825 G 200 mV Nonlinearity NL 200 100 mV Nonlinearity NL 100 Maximum Input Voltage |V | IN+ Before Output Clipping Average Input Bias ...
Page 7
AC Electrical Specifications All specifications and figures are at the nominal (typical) operating conditions and unless otherwise noted. A DD1 DD2 Parameter Symbol Min. Isolation Mode ...
Page 8
... RMS output noise. See applications section for more information. 12. Data sheet value is the amplitude of the transient at the differential output of the HCPL-7820/7825 when p-p 1 MHz square wave with 200 ns rise and fall times (measured at pins 1 and 8) is applied to both V and V ...
Page 9
... V – SUPPLY VOLTAGE – Figure 3. Input Offset Change vs. V DD1 and V . DD2 V DD1 1 0.1 µF 404 HCPL-7820/7825 13.2 3 0.01 µF 4 Figure 5. Gain and Nonlinearity Test Circuit. V +15 V DD2 0.1 µF 0.1 µ OUT 10 K – AD624CD GAIN = 100 0.1 µF 0.47 0.47 µF µF -15 V 4.0 3.5 NEGATIVE ...
Page 10
DD1 0 DD2 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -40 - 100 T – TEMPERATURE – °C A Figure 6. Gain Change vs. Temperature. 0.16 ...
Page 11
... ° 100 500 f – FREQUENCY – kHz Figure 19. Amplitude Response vs. Frequency. 78L05 IN OUT 1 0.1 0.1 µF µF 2 HCPL-7820/7825 PULSE GEN. 0.4 + Figure 16. Isolation Mode Rejection Test Circuit +15 V DD2 0.1 µF 8 0.1 µ – MC34081 0.1 µF ...
Page 12
... T – TEMPERATURE – °C A Figure 22. Dependence of Safety- Limiting Values on Temperature. VOLTAGE CLOCK REGULATOR GENERATOR ISO-AMP ENCODER MODULATOR INPUT Figure 23. HCPL-7820/7825 Block Diagram. FLOATING HV+ SUPPLY GATE DRIVE CIRCUIT FLOATING SUPPLY U1 78L05 IN OUT C1 0.1 µF MOTOR + – • • • ...
Page 13
... As shown in Figure 24, 0.1 F bypass capacitors (C2, C4) should be located as close as possible to the input and output power supply pins of the HCPL-7820/7825. The bypass capacitors are required because of the high-speed digital nature of the signals inside the isolation amplifier. A 0.01 F bypass capacitor (C3) is also rec- ...
Page 14
... PCB does not pass directly below or extend much wider than the HCPL-7820/7825. Using surface-mount components can help achieve many of the PCB objectives discussed in the pre- ceding paragraphs. An example ...
Page 15
... The offset of the op- amp should be low relative to the output offset of the HCPL-7820/ 7825, or less than about 5 mV. To maintain overall circuit band- width, the post-amplifier circuit should have a bandwidth at least ...