MAX9778ETI+ Maxim Integrated Products, MAX9778ETI+ Datasheet - Page 15

• Manufacturer Part Number: MAX9778ETI+
• Description: IC AMP AUDIO PWR 2.6W AB 28TQFN
• Manufacturer: Maxim Integrated Products
• Type: Class ABr

Specifications of MAX9778ETI+

• Output Type: 2-Channel (Stereo) with Stereo Headphones
• Max Output Power X Channels @ Load: 2.6W x 2 @ 4 Ohm; 200mW x 2 @ 16 Ohm
• Voltage - Supply: 4.5 V ~ 5.5 V
• Features: Depop, Input Multiplexer, Mute, Shutdown, Thermal Protection,
• Mounting Type: Surface Mount
• Package / Case: 28-TQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The MAX9777 recognizes a STOP condition at any
point during the transmission except if a STOP condi-
tion occurs in the same high pulse as a START condi-
tion (Figure 5). This condition is not a legal I
at least one clock pulse must separate any START and
STOP condition.
A REPEATED START (S
change of data direction on the bus. Such a change
occurs when a command word is required to initiate a
read operation. S
master is writing to several I
want to relinquish control of the bus. The MAX9777 ser-
ial interface supports continuous write operations with
or without an S
read operations require S
change in direction of data flow.
Figure 5. Early STOP Condition
SDA
SCL
SDA
SCL
r
condition separating them. Continuous
ILLEGAL EARLY STOP CONDITION
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
r
LEGAL STOP CONDITION
START
may also be used when the bus
Stereo 3W Audio Power Amplifiers with
STOP
REPEATED START Conditions
r
) condition may indicate a
r
conditions because of the
2
C devices and does not
START
ILLEGAL
Early STOP Conditions
STOP
Headphone Drive and Input Mux
2
C format;
The acknowledge bit (ACK) is the ninth bit attached to
any 8-bit data word. The receiving device always gen-
erates ACK. The MAX9777 generates an ACK when
receiving an address or data by pulling SDA low during
the night clock period. When transmitting data, the
MAX9777 waits for the receiving device to generate an
ACK. Monitoring ACK allows for detection of unsuc-
cessful data transfers. An unsuccessful data transfer
occurs if a receiving device is busy or if a system fault
has occurred. In the event of an unsuccessful data
transfer, the bus master should reattempt communica-
tion at a later time.
The bus master initiates communication with a slave
device by issuing a START condition followed by a 7-bit
slave address (Figure 6). When idle, the MAX9777
waits for a START condition followed by its slave
address. The LSB of the address word is the
Read/Write (R/W) bit. R/W indicates whether the master
is writing to or reading from the MAX9777 (R/W = 0
selects the write condition, R/W = 1 selects the read
condition). After receiving the proper address, the
MAX9777 issues an ACK by pulling SDA low for one
clock cycle.
The MAX9777 has a factory-/user-programmed
address. Address bits A6–A2 are preset, while A0 and
A1 is set by ADD. Connect ADD to either V
SCL, or SDA to change the last 2 bits of the slave
address
Figure 6. Slave Address Byte Definition
Table 2. MAX9777 I
ADD CONNECTION
S
(Table
GND
SDA
V
SCL
DD
A6
2).
A5
A4
2
C Slave Addresses
A3
Acknowledge Bit (ACK)
A2
I
2
C ADDRESS
100 1000
100 1001
100 1010
100 1011
A1
Slave Address
A0
DD
R/W
, GND,
15