PCD5042H Philips Semiconductors, PCD5042H Datasheet
PCD5042H
Available stocks
Related parts for PCD5042H
PCD5042H Summary of contents
Page 1
DATA SHEET PCD5042 DECT burst mode controller Objective specification File under Integrated Circuits, IC17 INTEGRATED CIRCUITS 1996 Oct 31 ...
Page 2
... RF interface 6.5.1 Serial receiver 6.5.2 Serial transmitter 6.5.3 Seamless handover 6.5.4 RF control signals 6.5.5 Synthesizer programming 6.5.6 RSSI measurement 6.5.7 Local call switching 6.5.8 Data synchronization 6.5.9 Ciphering machine 6.5.10 Comparator/data slicer on PCD5042HZ 6.6 Microcontroller Interface 6.6.1 Function of the microcontroller interface 6.6.2 Microcontroller interrupts 6.6.3 Watchdog 6.6.4 Power-down 6.7 Survey of registers 7 LIMITING VALUES 8 CHARACTERISTICS 9 PACKAGE OUTLINES 10 SOLDERING 10 ...
Page 3
... NUMBER NAME PCD5042H QFP64 plastic quad flat package; 64 leads (lead length 1.95 mm); body 14 PCD5042HZ LQFP80 plastic low profile quad flat package; 80 leads; body 12 1996 Oct 31 2 The PCD5042 DECT Burst Mode Controller (BMC custom IC that performs the DECT Physical Layer and ...
Page 4
... Philips Semiconductors DECT burst mode controller 4 BLOCK DIAGRAM handbook, full pagewidth to CODEC/ Highway 3-wire synthesizer interface Rx/Tx data 8051/68000 interface 5 PINNING (see Figs 2 and 3) PIN SYMBOL QFP64 AD0 to AD7 ALE A10 DD1 PROC_CLK SS1 XTAL1 17 XTAL2 ...
Page 5
... Philips Semiconductors DECT burst mode controller PIN SYMBOL QFP64 INT 24 CLK100 SS3 DO 27 FS3 FS1 28 FS4 FS2 DCK 31 CLK3 32 ANT_SW 33 T_ENABLE 34 T_POWER_RMP 35 RMT_STAT 36 SYNTH_LOCK SS4 REF_CLK DD2 S_ENABLE 41 S_CLK 42 S_DATA 43 S_POWER_DWN 44 VCO_BND_SW 45 1200 HZ 46 T_DATA 47 SET_OFF_IN 48 TEST1 ...
Page 6
... Philips Semiconductors DECT burst mode controller PIN SYMBOL QFP64 R_ENABLE 54 R_POWER_DWN 55 COMP_NE SLICE_CTR 56 COMP_OUT V 57 DD3 V 58 SS5 COMP_INM V 59 REF COMP_INP V 60 DD(RAM) SYNCPORT 61 RESET 62 MEM_SEL 63 EN_WATCHDOG 64 Notes 1. Un-referenced pins for the LQFP80 package are not connected. FS3, FS4 and the comparator signals are only available in the LQFP80 package ...
Page 7
... AD6 7 AD7 8 ALE 9 10 CSN 11 AD10 12 AD9 13 AD8 V DD1 14 PROC_CLK 15 V SS1 16 XTAL1 17 XTAL2 18 V SS2 19 1996 Oct 31 PCD5042H Fig.2 Pin configuration, PCD5042H (QFP64 package). 7 Objective specification PCD5042 51 TEST2 50 RSSI_AN 49 TEST1 48 SET_OFF_IN 47 T_DATA 46 1200_Hz 45 VCO_BND_SW 44 S_POWER_DWN 43 S_DATA 42 S_CLK 41 S_ENABLE V DD2 40 ...
Page 8
... AD6 7 AD7 8 ALE 9 n.c. 10 CSN 11 AD10 12 AD9 13 AD8 14 V DD1 15 PROC_CLK 16 V SS1 17 n.c. 18 n.c. 19 XTAL1 20 Fig.3 Pin configuration, PCD5042HZ (LQFP80 package). 1996 Oct 31 PCD5042HZ 8 Objective specification PCD5042 60 RSSI_AN 59 n.c. 58 TEST1 SET_OFF_IN 57 56 T_DATA 55 1200_Hz 54 VCO_BND_SW S_POWER_DWN 53 52 S_DATA S_CLK 51 50 n.c. ...
Page 9
... Philips Semiconductors DECT burst mode controller 6 FUNCTIONAL DESCRIPTION (see Fig.1) The PCD5042 has dedicated hardware blocks containing logic for time-critical functions requiring bit or byte-time accuracy. Other functions requiring only slot-time accuracy are performed by software in the Preprogrammed Communication Controller (PCC). This approach offers maximum flexibility during prototyping. ...
Page 10
... Philips Semiconductors DECT burst mode controller handbook, full pagewidth 3.456 MHz system clock for ADPCM codec 144 FSx signals (8 kHz) 6.4 Speech interface The speech interface block performs the following functions: Connection to a 1152 kbits/s interface in a handset and a simple base station in the so called ‘12 slot mode’ ...
Page 11
... Philips Semiconductors DECT burst mode controller data, these disturbances are not audible (or are less audible) to the user. The PCD5042 performs two types of muting: Fast muting Slow muting. Fast muting, which is performed by the PCD5042 automatically, is nothing more than a repetition of the previously received frame (80 speech samples) to the ADPCM CODEC ...
Page 12
... Philips Semiconductors DECT burst mode controller handbook, full pagewidth R-CRC handbook, full pagewidth R-CRC 1996 Oct 31 DATA MEMORY DATA MEMORY READ CONTROL DE-CIPHER CIPHER CONTROL other cs MUX Cs-DEC. ok A-MAP D-MAP D00 D32 Fig.6 Serial receiver structure. DATA MEMORY DATA MEMORY READ CONTROL ...
Page 13
... Philips Semiconductors DECT burst mode controller 6.5.3 S EAMLESS HANDOVER Seamless handover guarantees that when speech information is switched from one slot to another, no speech samples are lost, added or displaced. Seamless handover is achieved in the RF interface by: Using a look-up table containing the correct start addresses of the B-fields in the data memory The RF receive and transmit blocks move data to/from the data memory block in 4-bit nibbles ...
Page 14
... Philips Semiconductors DECT burst mode controller 6.5.7 L OCAL CALL SWITCHING The PCD5042 provides a local call switching function in the base station. It will store incoming speech nibbles in the common data memory, in the area reserved for that particular receive slot. Then, during the transmit phase, it passes the start pointer of the same data memory area to the transmit block ...
Page 15
... PCC, and the external microprocessor. 6.5.10 C OMPARATOR The PCD5042HZ contains a comparator/data slicer. The comparator is a stand-alone circuit. No connections other than power supply are made internally. The comparator can be used as a data slicer for the receiver input. The delay requirements listed in Chapter 8 were derived from this application ...
Page 16
... Philips Semiconductors DECT burst mode controller 6.6 Microcontroller Interface 6.6.1 F UNCTION OF THE MICROCONTROLLER INTERFACE The microcontroller Interface will provide the following services. Direct interface to processors which have an INTEL-8051 compatible interface General interface to processors that can handle ‘wait states’ e.g. 68000-family; in this case glue logic is ...
Page 17
... Philips Semiconductors DECT burst mode controller Table 1 Hardware register addresses ADDRESS WRITE 7E0 7E1 S-DATA1 7E2 S-DATA2 7E3 S-DATA3 7E4 7E5 B-field-shift 7E6 B-field-loc. 7E7 A-field-loc. 7E8 window-wide-off 7E9 window-wide-on 7EA window-narrow-off 7EB window-narrow-on 7EC T-power-rmp-on 7ED synth-off 7EE RF-control-port 7EF ...
Page 18
... Philips Semiconductors DECT burst mode controller 7 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL V supply voltage DD V all input voltages input current output current O P total power dissipation tot P power dissipation per output O I supply current ...
Page 19
... REF Z V input impedance i(VREF) REF t conversion time conv integral non-linearity differential non-linearity Z input impedance RSSI_AN i(RSSI_AN) PCD5042HZ comparator characteristics I supply current (standby) DD(stb)(comp) I supply current (idle) DD(idle)(comp) I supply current (1 MHz) DD(1MHz) I input leakage current LI(comp) C input capacitance ...
Page 20
... Philips Semiconductors DECT burst mode controller Notes to the characteristics 3 =13.824 MHz; no external load; one speech link active (under typical conditions). DD clk 3 =13.824 MHz; no external load; after reset. DD clk 3. Maximum differential non-linearity at supply voltage 5.5 V and V 4. Supply current I ...
Page 21
... Philips Semiconductors DECT burst mode controller 9 PACKAGE OUTLINES QFP64: plastic quad flat package; 64 leads (lead length 1.95 mm); body 2.7 mm; high stand-off height pin 1 index DIMENSIONS (mm are the original dimensions) A UNIT max. 0.36 2.87 mm 3.3 0.25 0.10 2.57 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. ...
Page 22
... Philips Semiconductors DECT burst mode controller LQFP80: plastic low profile quad flat package; 80 leads; body 1 pin 1 index DIMENSIONS (mm are the original dimensions) A UNIT max. 0.16 1.5 mm 1.6 0.25 0.04 1.3 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. ...
Page 23
... Philips Semiconductors DECT burst mode controller 10 SOLDERING 10.1 Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities ...
Page 24
... Philips Semiconductors DECT burst mode controller 11 DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains fi ...
Page 25
... Philips Semiconductors DECT burst mode controller 1996 Oct 31 NOTES 25 Objective specification PCD5042 ...
Page 26
... Philips Semiconductors DECT burst mode controller 1996 Oct 31 NOTES 26 Objective specification PCD5042 ...
Page 27
... Philips Semiconductors DECT burst mode controller 1996 Oct 31 NOTES 27 Objective specification PCD5042 ...
Page 28
... Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381 Middle East: see Italy For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. + 24825 © Philips Electronics N.V. 1996 All rights are reserved ...