MT8941AP Mitel, MT8941AP Datasheet
MT8941AP
Available stocks
Related parts for MT8941AP
MT8941AP Summary of contents
Page 1
... Bi Yo CMOS ST-BUS Advanced T1/CEPT Digital Trunk PLL MT8941AE MT8941AP Description The MT8941 is a dual digital phase-locked loop providing the timing and synchronization signals for the T1 or CEPT transmission links and the ST-BUS. The first PLL provides the T1 clock (1.544 MHz) synchronized to the input frame pulse at 8 kHz ...
Page 2
MT8941 CMOS 1 24 ENVC 2 23 MS0 22 C12i 3 21 MS1 F0i 19 F0b 6 18 MS2 7 17 C16i 8 ENC4o 16 9 C8Kb 15 10 C4o VSS 12 24 PIN ...
Page 3
Pin Description (continued) Pin # Name DIP PLCC 13 15 C4b Clock 4.096 MHz- Bidirectional (TTL compatible input and Totem-pole output) - When the mode select bit MS3 (pin 17) is HIGH, it provides the 4.096 MHz clock output with ...
Page 4
... Figure 4. The maximum phase variation for DPLL #1 is 324 ns and for DPLL # 32µs. However, this phase difference can be absorbed by the input jitter buffer of Mitel’s T1/CEPT devices. The no-correction window acts as a filter for low frequency jitter and wander since the DPLL does not track the reference signal inside it ...
Page 5
... The inputs MS0 to MS3 are used to select the operating mode of the MT8941, see Tables All the outputs are controlled to the high impedance condition by their respective enable controls. The uncommitted NAND gate is available for use in applications involving Mitel’s MT8976/ MH89760 (T1 Interfaces) and MT8979/MH89790 Interfaces). ...
Page 6
MT8941 CMOS The operation of DPLL #2 in SINGLE CLOCK-1 mode is identical to SINGLE CLOCK-2 mode, providing the CEPT and ST-BUS compatible timing signals synchro-nized to the internal 8 kHz signal obtained from DPLL#1 in DIVIDE mode. SINGLE CLOCK-1 ...
Page 7
When MS3 is HIGH, DPLL #2 operates in any of the major modes selected by MS0 and MS1. When MS3 is LOW, it overrides the major mode selected and DPLL#2 accepts an external clock of 4.096 MHz on C4b (pin ...
Page 8
MT8941 CMOS Fig. 5- The Spectrum of the Inherent Jitter for either PLL Fig The Jitter Transfer Function for PLL1 Fig The Jitter Transfer Function for PLL2 3-50 ...
Page 9
DPLL #1 and DPLL #2 to have maximum tolerances of ±32ppm and ±50ppm respectively. However, if DPLL #1 and DPLL #2 are daisy-chained as shown in Figures 9 and 10, the output clock tolerance of DPLL #1 will ...
Page 10
... Applications The following figures illustrates how the MT8941 can be used in a minimum component count approach in providing the timing and synchro-nization signals for In the Mitel T1 or CEPT interfaces, and the ST-BUS. of the The hardware independent control over each PLL adds flexibility to the interface circuits ...
Page 11
... CEPT Transmission Link The MT8941 can be used to provide the timing and synchronization signals for the MH89790/790B, Mitel’s CEPT (30+2) Digital Trunk Interface Hybrid. Since the operational frequencies of the ST-BUS and the CEPT primary multiplex digital trunk are the same, only DPLL #2 is required. ...
Page 12
... V does not make any corrections and therefore, the output signals are free from jitter. completely free. For prototyping purposes, Mitel offers the MT8941 Crystal Kit (MB6022) which contains 16.384 MHz and 12.352 MHz clock oscillators. DPLL #1 - NOT USED DPLL #2 - FREE-RUN MODE (MS0=0 ...
Page 13
Absolute Maximum Ratings* Parameter 1 Supply Voltage 2 Voltage on any pin 3 Input/Output Diode Current 4 Output Source or Sink Current 5 DC Supply or Ground Current 6 Storage Temperature 7 Package Power Dissipation * Exceeding these values may ...
Page 14
MT8941 CMOS AC Electrical Characteristics Characteristics 1 CVb output (1.544 MHz) rise time 2 CVb output (1.544 MHz) fall time D 3 CVb output (1.544 MHz) clock P period CVb output (1.544 MHz) clock width (HIGH) #1 ...
Page 15
V IH CVb ICHL C8HH V OH C8Kb F0b FPL t W4oH V OH C4b W4oL V OH C4o V OL ...
Page 16
MT8941 CMOS AC Electrical Characteristics Characteristics 1 C4b output clock period 2 C4b output clock width (HIGH) 3 C4b output clock width (LOW) 4 C4b output clock rise time 5 C4b clock output fall time 6 Frame pulse output delay ...
Page 17
AC Electrical Characteristics Characteristics 1 Master clocks input rise time 2 Master clocks input fall time 3 C Master clock period L (12.352MHz Master clock period C (16.384MHz Duty Cycle of master clocks 6 Lock-in ...
Page 18
MT8941 CMOS AC Electrical Characteristics Characteristics 1 Delay from Enable to Output (HIGH to THREE STATE Delay from Enable to Output U (LOW to THREE STATE Delay from Enable to Output U (THREE STATE to ...