MC145480 Freescale Semiconductor, Inc, MC145480 Datasheet
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
MC145480
Available stocks
Related parts for MC145480
MC145480 Summary of contents
Page 1
... MOTOROLA SEMICONDUCTOR TECHNICAL DATA 5 V PCM Codec-Filter The MC145480 is a general purpose per channel PCM Codec–Filter with pin selectable Mu–Law or A–Law companding, and is offered in 20–pin DIP, SOG, and SSOP packages. This device performs the voice digitization and reconstruction as well as the band limiting and smoothing required for PCM systems. This device is designed to operate in both synchronous and asynchronous applications and contains an on– ...
Page 2
... The low–pass filter used to at- tenuate these aliasing components is typically called a re- construction or smoothing filter. The MC145480 PCM Codec–Filter has the codec, both presampling and reconstruction filters, a precision voltage reference on–chip, and requires no external components. ...
Page 3
... This pin is capable of driving a 300 load to PO+. The PO+ and PO– outputs are differential (push–pull) and capable of driving a 300 3.15 V peak, which is 6.3 V peak–to–peak. The bias voltage and signal reference of this output is the V AG pin. The V AG load to MC145480 3 ...
Page 4
... PCM data. When operating in the IDL or GCI mode, data is output in either the channel as selected by FSR. This pin is high impedance when the device is in the powered down mode. MC145480 4 FSR Frame Sync, Receive (Pin 7) When used in the Long Frame Sync or Short Frame Sync mode, this pin accepts an 8 kHz clock, which synchronizes the input of the serial PCM data at the DR pin ...
Page 5
... Long Frame Sync, Short Frame Sync, IDL mode, or GCI mode). DIGITAL I/O The MC145480 is pin selectable for Mu–Law or A–Law. Table 1 shows the 8–bit data word format for positive and negative zero and full scale for both companding schemes (see Tables 3 and 4 at the end of this document for a com- plete PCM word conversion table) ...
Page 6
... Figure NO TAGc. IDL Interface — BCLKR = 1 (Transmit and Receive Have Common FSC (FST) DCL (BCLKT) D out (DT) 1 DON’ (DR) 1 CARE B1–CHANNEL (FSR = 0) Figure NO TAGd. GCI Interface — BCLKR = 0 (Transmit and Receive Have Common Figure 2. Digital Timing Modes for the PCM Data Interface MC145480 ...
Page 7
... FST, FSR, BCLKT, DT, and DR. The IDL Interface consists of four pins: IDL SYNC (FST), IDL CLK (BCLKT), IDL TX (DT), and IDL RX (DR). The IDL interface mode provides access to both the transmit and receive PCM data words with common control clocks of IDL Sync and IDL Clock. In this mode, the MC145480 7 ...
Page 8
... DCL rising edge after the FSC rising edge. PRINTED CIRCUIT BOARD LAYOUT CONSIDERATIONS The MC145480 is manufactured using high–speed CMOS VLSI technology to implement the complex analog signal processing functions of a PCM Codec–Filter. The fully–differ- ential analog circuit design techniques used for this device result in superior performance for the switched capacitor fil- ters, the analog– ...
Page 9
... The V AG pin cannot be used for ESD or line protection. 9. For applications using multiple MC145480 PCM Codec– Filters, the V AG pins cannot be tied together. The V AG pins are capable of sourcing and sinking current and will ...
Page 10
... Output High Voltage (DT Pin – 2.5 mA) Input Low Current ( Input High Current ( Output Current in High Impedance State (V SS Input Capacitance of Digital Pins (Except DT) Input Capacitance of DT Pin when High–Z MC145480 10 Symbol Min 4.75 (No Load – 0.5 V) — (No Load – 1.5 V) — ...
Page 11
... V DD – 1.0 — — mA — — — — 500 pF — 2.4 2 — — dBC 75 — 0.05 1.0 mA — — M — — — — — 1000 — kHz — 1000 0 — dBC 55 — — MC145480 11 ...
Page 12
... Intermodulation Distortion of Two Frequencies of Amplitudes (– – 21 dBm0 from the Range 300 to 3400 Hz) NOTES: 1. Extrapolated from a 1020 Hz @ – 50 dBm0 distortion measurement to correct for encoder enhancement. 2. Selectively measured while stimulated with 2667 Hz @ – 50 dBm0. MC145480 12 End–to–End Min Max — ...
Page 13
... MC145480 13 ...
Page 14
... MCLK 1 BCLKT 11 FST 16 MSB DT 1 BCLKR 11 12 FSR MSB DR MC145480 CH1 CH2 CH3 ST1 CH1 CH2 CH3 ST1 Figure 3. Long Frame Sync Timing ST2 ST3 ...
Page 15
... DT 1 BCLKR FSR 13 MSB DR MOTOROLA CH1 CH2 CH3 ST1 CH1 CH2 CH3 ST1 Figure 4. Short Frame Sync Timing ST2 ST3 LSB ST2 ST3 LSB MC145480 15 ...
Page 16
... IDLE SYNC (FST IDL CLOCK (BCLKT IDL TX MSB CH1 CH2 CH3 (DT IDL RX MSB CH1 CH2 CH3 (DR) MC145480 16 Characteristics ST1 ST2 ST3 LSB MSB CH1 CH2 CH3 38 37 ...
Page 17
... Max Unit Note 2 512 6176 kHz 50 — — — — ns — — — — ns — CH3 ST1 ST2 ST3 LSB 53 CH3 ST1 ST2 ST3 LSB MC145480 17 ...
Page 18
... Figure 7. MC145480 Test Circuit with Differential Input and Output AUDIO OUT AUDIO OUT 150 0.1 F Figure 8. MC145480 Test Circuit with Input and Output Referenced MC145480 RO RO– TI TI– ...
Page 19
... 1/2 MC74HC73 K GND 8 kHz 256 2.048 MHz Figure 9. Long Frame Sync Clock Circuit for 2.048 MHz SIDETONE REC + Figure 10. MC145480 Analog Interface to Handset with IDL Clocking MOTOROLA 2.048 MHz 300 R OSC IN OSC OSC OUT 1 OUT 2 MC74HC4060 ...
Page 20
... R0 = 600 TIP RING + 5 V 0.1 F Figure 11. MC145480 Transformer Interface to 600 R0 = 600 TIP N = 0.5 1 0.5 – 0.5 RING 0.1 F Figure 12. MC145480 Step–Up Transformer Interface to 600 MC145480 RO– TI TI– 4 PO– Mu/A PO+ ...
Page 21
... Normalized Decode Step Step Step Levels 8031 4191 2079 1023 495 231 MC145480 21 ...
Page 22
... NOTES: 1. Characteristics are symmetrical about analog zero with sign bit = 0 for negative analog values. 2. Digital code includes inversion of all even numbered bits. MC145480 22 Digital Code Sign Chord Chord Chord Step ...
Page 23
... TOTAL IN EXCESS OF D DIMENSION AT MAXIMUM MATERIAL CONDITION. MILLIMETERS INCHES DIM MIN MAX MIN MAX A 12.65 12.95 0.499 0.510 B 7.40 7.60 0.292 0.299 C 2.35 2.65 0.093 0.104 D 0.35 0.49 0.014 0.019 F 0.50 0.90 0.020 0.035 G 1.27 BSC 0.050 BSC _ J 0.25 0.32 0.010 0.012 K 0.10 0.25 0.004 0.009 10.05 10.55 0.395 0.415 R 0.25 0.75 0.010 0.029 MC145480 23 ...
Page 24
... DETERMINED AT DATUM PLANE –W–. MILLIMETERS INCHES DIM MIN MAX MIN MAX A 7.07 7.33 0.278 0.288 B 5.20 5.38 0.205 0.212 C 1.73 1.99 0.068 0.078 D 0.05 0.21 0.002 0.008 F 0.63 0.95 0.024 0.037 G 0.65 BSC 0.026 BSC H 0.59 0.75 0.023 0.030 J 0.09 0.20 0.003 0.008 J1 0.09 0.16 0.003 0.006 K 0.25 0.38 0.010 0.015 K1 0.25 0.33 0.010 0.013 L 7.65 7.90 0.301 0.311 *MC145480/D* MC145480/D MOTOROLA ...