LT1006 Linear Technology Corporation, LT1006 Datasheet
LT1006
Available stocks
Related parts for LT1006
LT1006 Summary of contents
Page 1
... Its design has been optimized for single supply operation with a full set of specifications at 5V. Specifications at ±15V are also provided. The LT1006 has a low offset voltage of 20µV, drift of 0.2µV/°C, offset current of 120pA, gain of 2.5 million, common mode rejection of 114dB and power supply rejection of 126dB. Although supply current is only 340µ ...
Page 2
... Input Noise Current Density n Input Resistance Differential Mode Common Mode 2 U (Note 1) Operating Temperature Range LT1006AM/LT1006M (OBSOLETE)....– 55°C to 125°C LT1006AC/LT1006C/LT1006S8 ............... 0°C to 70°C Storage Temperature Range ................. – 65°C to 150°C Lead Temperature (Soldering, 10 sec).................. 300° ORDER PART NUMBER V ...
Page 3
... V = 0.1V 1.4V LT1006AM LT1006M TYP MAX MIN TYP MAX 40 180 60 250 0.2 1.3 0.3 1.8 0.4 2.0 0.5 4 0.8 0.15 0.7 103 87 102 117 97 116 3.8 3.1 3.8 380 630 400 680 UNITS V ...
Page 4
... ±2V to ±18V 106 ±10V 1 ±10V 600Ω 0 ± ∞ 0.25 SET R = 390Ω Pin 8 to Pin 4 1.0 SET LT1006AC LT1006C TYP MAX MIN TYP MAX 30 110 45 160 50 190 110 560 0.2 1.3 0.3 1.8 0.5 2.5 0.7 3.5 0.25 1.2 0.3 2 1.3 0.25 1.2 109 ...
Page 5
... T ≤ 70°C, unless otherwise S A LT1006AC LT1006C TYP MAX MIN TYP MAX 50 200 75 300 80 330 150 730 0.5 2.2 0.6 2.8 0.7 3.5 1.0 4.5 0. 0.7 2.5 116 94 114 120 ...
Page 6
... TEMPERATURE (°C) LT1006 • G02 Warm-Up Drift 2 5V 25°C A 1.5 1.0 0.5 LT1006 METAL CAN (H) PACKAGE LT1006 CERDIP (J) PACKAGE TIME AFTER POWER ON (MIN) LT1006 • G05 Input Bias Current vs Temperature 5V ± ...
Page 7
... V = ±15V 5V PIN 8 IS APPROXIMATELY 60mV ABOVE THE NEGATIVE SUPPLY 0.1 100 PIN 8 TO PIN 4 (Ω) SET LT1006 • G16 Common Mode Rejection Ratio vs Frequency 120 100 100 1k 10k FREQUENCY (Hz) ...
Page 8
... Power Supply Rejection Ratio vs Frequency 120 100 POSITIVE NEGATIVE 80 SUPPLY SUPPLY ±15V + 1Vp-p SINE WAVE 25° 100k 0 100 10k FREQUENCY (Hz) LT1006 • G22 Large-Signal Transient Response ±15V S 5V/DIV 50µs/DIV 1006 G25 2µs/DIV 1006 G27 1M 1006fa ...
Page 9
... When the input is more than a diode drop below ground, unlimited current will flow from the substrate (V nal) to the input. This can destroy the unit. On the LT1006, the 400Ω resistors, in series with the input (see Schematic Diagram), protect the devices even when the input is 5V below ground ...
Page 10
... LT1007 or LT1028 data sheet. Supply Current Programming Connecting an optional external resistor to Pin 8 changes the biasing of the LT1006 in order to increase its speed or to decrease its power consumption higher slew rate is required, connect the external resistor for Pin 8 to Pin 4 ...
Page 11
... V IN 1/2 LTC1043 I = OUT 100Ω 0.001µF OPERATES FROM A SINGLE 5V SUPPLY LT1006 • TA06 9V LM334 2k REFERENCE 74C90 74C90 LT1004-2.5 100 LT1004-1.2 OUTPUT 0MHz TO 1MHz ...
Page 12
... TRW MAR-6 0. YELLOW SPRINGS INST MODEL 44007 5k AT 25°C LT1006 • TA08 1.000V = LT1006 0°C TO 100.0°C ±0.25°C 2 – 4 51.1k 500Ω 100°C 100k T1 = YELLOW SPRINGS #44201 ALL RESISTORS = TRW MAR-6 0.1% UNLESS NOTED LT1006 • TA09 1006fa ...
Page 13
... LT1006 V OUT 4 – LT1006 • TA10 1k Q38 Q30 Q35 J1 Q25 Q33 Q37 Q26 2.4k 18Ω Q39 Q40 6 28k OUTPUT 4pF Q31 2k Q42 Q34 100pF Q23 Q24 Q44 1.3k 2k 30Ω 84k 5.4k LT1006 • SD01 600Ω Q36 – V Q41 Q43 8 2.5k 1006fa 13 ...
Page 14
... LT1006 PACKAGE DESCRIPTIO .045 – .068 (1.143 – 1.650) FULL LEAD OPTION .300 BSC (7.62 BSC) .008 – .018 (0.203 – 0.457) NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS Package 8-Lead TO-5 Metal Can (.200 Inch PCD) (Reference LTC DWG # 05-08-1320) .335 – ...
Page 15
... PDIP (Narrow .300 Inch) (Reference LTC DWG # 05-08-1510) 8 .255 ± .015* (6.477 ± 0.381) 1 .045 – .065 (1.143 – 1.651) .065 (1.651) TYP .100 (2.54) BSC INCHES LT1006 .400* (10.160) MAX .130 ± .005 (3.302 ± 0.127) .120 .020 (3.048) MIN (0 ...
Page 16
... LT1006 PACKAGE DESCRIPTIO .050 BSC N .245 MIN 1 2 .030 ±.005 TYP RECOMMENDED SOLDER PAD LAYOUT .010 – .020 (0.254 – 0.508) .008 – .010 (0.203 – 0.254) NOTE: 1. DIMENSIONS IN 2. DRAWING NOT TO SCALE 3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. ...