AT93C46A ATMEL Corporation, AT93C46A Datasheet
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT93C46A
Available stocks
Related parts for AT93C46A
AT93C46A Summary of contents
Page 1
... The AT93C46A is available in space-saving 8- lead PDIP, 8-lead JEDEC SOIC, and 8-lead TSSOP packages. The AT93C46A is enabled through the Chip Select pin (CS) and accessed via a three- wire serial interface consisting of Data Input (DI), Data Output (DO), and Shift Clock (SK). Upon receiving a Read instruction at DI, the address is decoded and the data is clocked out serially on the data output DO pin ...
Page 2
... Table 2-2. Pin Capacitance Applicable over recommended operating range from T Symbol Test Conditions C Output Capacitance (DO) OUT C Input Capacitance (CS, SK, DI) IN Note: This parameter is characterized and is not 100% tested. AT93C46A 2 *NOTICE: Block Diagram MEMORY ARRAY DATA REGISTER MODE DECODE LOGIC CLOCK GENERATOR = 25° ...
Page 3
Table 2-3. DC Characteristics Applicable over recommended operating range from: T Symbol Parameter V Supply Voltage CC1 V Supply Voltage CC2 V Supply Voltage CC3 I Supply Current CC I Standby Current SB1 I Standby Current SB2 I Standby Current ...
Page 4
... Output Delay to “0” PD0 Status Valid High t DF Impedance t Write Cycle Time WP (1) Endurance 5.0V, 25°C Note: 1. This parameter is characterized and is not 100% tested. AT93C46A 4 = −40° 85° Test Condition 4.5V ≤ V ≤ 5.5V CC 2.7V ≤ V ≤ 5.5V CC 1.8V ≤ V ≤ 5.5V CC 4.5V ≤ V ≤ 5.5V CC 2.7V ≤ ...
Page 5
... Functional Description The AT93C46A is accessed via a simple and versatile three-wire serial communication inter- face. Device operation is controlled by seven instructions issued by the host processor. A valid instruction starts with a rising edge of CS and consists of a start bit (logic “1”) followed by the appropriate op code and the desired memory address location. ...
Page 6
... EWEN and EWDS instructions and can be executed at any time. 4. Timing Diagrams Figure 4-1. Synchronous Data Timing Note: 1. This is the minimum SK period. Table 4-1. AT93C46A 6 = 5.0V ± 10%. CC µ s (1) Organization Key for Timing Diagrams I The WRAL instruction is CS AT93C46A 0539L–SEEPR–11/07 ...
Page 7
Figure 4-2. READ Timing High Impedance (1) Figure 4-3. EWEN Timing Note: 1. Requires a minimum of nine clock cycles. (1) Figure 4-4. EWDS Timing Note: 1. Requires a minimum ...
Page 8
... HIGH IMPEDANCE DO ((1)),( (2)) Figure 4-6. WRAL Timing HIGH IMPEDANCE DO Notes: 1. Valid only 4.5V to 5.5V Requires a minimum of nine clock cycles. Figure 4-7. ERASE Timing HIGH IMPEDANCE DO AT93C46A 8 ... ... ... ... N N-1 N BUSY READY t WP ...
Page 9
Figure 4-8. ERAL Timing HIGH IMPEDANCE DO Note: 1. Valid only 4.5V to 5.5V. CC 0539L–SEEPR–11/ STANDBY CHECK STATUS BUSY HIGH IMPEDANCE ...
Page 10
... Ordering Information Ordering Code AT93C46A-10PU-2.7 AT93C46A-10PU-1.8 AT93C46A-10SU-2.7 AT93C46A-10SU-1.8 AT93C46A-10TU-2.7 AT93C46A-10TU-1.8 Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values page 4 . Not recommended for new design. Please see AT93C46E datasheet. 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" ...
Page 11
Packaging Information 5.1 8P3 – PDIP Top View PLCS Side View Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L ...
Page 12
... JEDEC SOIC Top View e Side View Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R AT93C46A TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing ...
Page 13
TSSOP Pin 1 indicator this corner N Top View Side View Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, ...
Page 14
... Revision History Doc. Rev. 0539L 0539K AT93C46A 14 Date Comments 11/2007 Modified ‘max’ values on DC/AC Characteristics tables. Implemented revision history. Added Note to page 1 and ordering information; Not 2/2007 recommended for new design; please refer to AT93C46E datasheet. 0539L–SEEPR–11/07 ...
Page 15
... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2007 Atmel Corporation. All rights reserved. Atmel of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. International Atmel Asia ...