MAX9704ETJ+T Maxim Integrated Products, MAX9704ETJ+T Datasheet - Page 8
![IC AMP AUDIO PWR 16W STER 32TQFN](/photos/6/50/65019/32-tqfn_21-0140l_sml.jpg)
MAX9704ETJ+T
Manufacturer Part Number
MAX9704ETJ+T
Description
IC AMP AUDIO PWR 16W STER 32TQFN
Manufacturer
Maxim Integrated Products
Type
Class Dr
Datasheet
1.MAX9703ETJ.pdf
(20 pages)
Specifications of MAX9704ETJ+T
Output Type
2-Channel (Stereo)
Max Output Power X Channels @ Load
16W x 2 @ 16 Ohm
Voltage - Supply
10 V ~ 25 V
Features
Depop, Differential Inputs, Mute, Short-Circuit and Thermal Protection, Shutdown
Mounting Type
Surface Mount
Package / Case
32-TQFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
10W Stereo/15W Mono, Filterless,
Spread-Spectrum, Class D Amplifiers
The MAX9703/MAX9704 filterless, Class D audio power
amplifiers feature several improvements to switch-
mode amplifier technology. The MAX9703 is a mono
amplifier, the MAX9704 is a stereo amplifier. These
devices offer Class AB performance with Class D effi-
ciency, while occupying minimal board space. A
unique filterless modulation scheme and spread-spec-
trum switching mode create a compact, flexible, low-
noise, efficient audio power amplifier. The differential
input architecture reduces common-mode noise pick-
up, and can be used without input-coupling capacitors.
The devices can also be configured as a single-ended
input amplifier.
Comparators monitor the device inputs and compare
the complementary input voltages to the triangle wave-
form. The comparators trip when the input magnitude of
the triangle exceeds their corresponding input voltage.
The MAX9703/MAX9704 feature three FFM modes with
different switching frequencies (Table 1). In FFM mode,
the frequency spectrum of the Class D output consists of
the fundamental switching frequency and its associated
harmonics (see the Wideband Output Spectrum (FFM
Mode) graph in the Typical Operating Characteristics).
The MAX9703/ MAX9704 allow the switching frequency to
be changed by ±35%, should the frequency of one or
more of the harmonics fall in a sensitive band. This can be
done at any time and does not affect audio reproduction.
The MAX9703/MAX9704 feature a unique spread-spec-
trum mode that flattens the wideband spectral compo-
nents, improving EMI emissions that may be radiated
8
_______________________________________________________________________________________
Spread-Spectrum Modulation (SSM) Mode
Fixed-Frequency Modulation (FFM) Mode
Detailed Description
Operating Modes
by the speaker and cables. This mode is enabled by
setting FS1 = FS2 = H. In SSM mode, the switching fre-
quency varies randomly by ±7% around the center fre-
quency (670kHz). The modulation scheme remains the
same, but the period of the triangle waveform changes
from cycle to cycle. Instead of a large amount of spec-
tral energy present at multiples of the switching fre-
quency, the energy is now spread over a bandwidth
that increases with frequency. Above a few megahertz,
the wideband spectrum looks like white noise for EMI
purposes (see Figure 1).
Efficiency of a Class D amplifier is attributed to the
region of operation of the output stage transistors. In a
Class D amplifier, the output transistors act as current-
steering switches and consume negligible additional
power. Any power loss associated with the Class D out-
put stage is mostly due to the I
on-resistance, and quiescent current overhead.
The theoretical best efficiency of a linear amplifier is
78%; however, that efficiency is only exhibited at peak
output powers. Under normal operating levels (typical
music reproduction levels), efficiency falls below 30%,
whereas the MAX9704 still exhibits >78% efficiency
under the same conditions (Figure 2).
Table 1. Operating Modes
FS1
H
H
L
L
FS2
H
H
L
L
2
R loss of the MOSFET
SWITCHING MODE
670 ±7%
Efficiency
(kHz)
670
940
470