BGB100 Philips Semiconductors, BGB100 Datasheet
BGB100
Available stocks
Related parts for BGB100
BGB100 Summary of contents
Page 1
... DISCRETE SEMICONDUCTORS DATA SHEET BGB100 0 dBm TrueBlue radio module Preliminary specification 2002 Jan 03 ...
Page 2
... Internal shielding for better EMI (Electro Magnetic Interference) immunity. DESCRIPTION The BGB100 TrueBlue Bluetooth radio module is a short-range radio transceiver for wireless links operating in the globally available ISM band, between 2402 and 2480 MHz composed of a fully integrated, ...
Page 3
... Jan 03 DESCRIPTION PLL loop VCO filter tank Regulator Control logic Synthesizer Demod DC extractor balun + filter R_DATA DCXCTR RSSI Fig.2 Block diagram. 3 Preliminary specification Pin 23 represents the inner LGA pads Fig.1 Simplified outline balun + filter Band Tx/Rx pass switch filter BGB100 ANT ...
Page 4
... FUNCTIONAL DESCRIPTION Control The BGB100 TrueBlue Bluetooth Radio Module is controlled by a baseband processor via the serial 3-wire bus. These 3 wires are data (S_DATA), clock (S_CLK) and enable (S_EN). Data sent to the device is loaded in bursts framed by S_EN. Data and clock (S_DATA and S_CLK) signals are ignored until S_EN goes low. The programmed information is read directly into the internal registers when S_EN goes high ...
Page 5
... Due to the IF frequency at 1 MHz mode the VCO frequency should be 1 MHz higher than the channel frequency. This should be taken care of by the baseband controller. Power-down mode In Power-down mode, current consumption is reduced to below 60 µA. The 3-wire bus inputs present a high-ohmic resistance to ground. 2002 Jan 03 5 Preliminary specification BGB100 ...
Page 6
... FREQUENCY RATIO (MHz) 1.0 × (2304 +n) 2304 + n 2402 2402 2403 2403 2480 2480 2481 2481 REFERENCE INPUT RATIO BGB100 b17 b16 see below 1 0 CHANNEL FREQUENCY TX channel 1 RX channel 1 TX channel 2 RX channel 78 TX channel 79 RX channel 79 FREQUENCY 12 MHz 16 MHz 13 MHz ...
Page 7
... PARAMETER ESD threshold voltage HBM (JESD22-A114-B) MM (JESD22-A115-A) 2002 Jan 03 b10 CONDITIONS PARAMETER METHOD VALUE ≥3500 V ≥300 V 7 Preliminary specification BGB100 TYPICAL OUTPUT POWER −4.5 dBm −1.5 dBm (nominal value) 1.5 dBm 3.5 dBm MIN. MAX. UNIT −0.3 3.6 V −0 − 0.01 V − ...
Page 8
... MHz offset; measured in 100 kHz bandwidth; referred to wanted channel = 50 Ω normalized referred to wanted output level 2450 MHz 1225 MHz VCO 8 Preliminary specification BGB100 MIN. TYP. MAX. UNIT 2.8 3.0 3.6 V − − − − ...
Page 9
... BER < 0.1 % wanted signal −60dBm; BER < 0.1 % wanted signal −60dBm; BER < 0.1 % wanted signal −67dBm; BER < 0.1 % wanted signal −67dBm; BER < 0.1 % wanted signal −67dBm; BER < 0 Preliminary specification BGB100 MIN. TYP. MAX. UNIT − −36 tbd dBm − −30 tbd dBm − ...
Page 10
... HIGH or LOW level note 4 to switch off the module: note 3 for R_DATA output for R_DATA output at 500 kHz at 500 kHz note 2 at 500 kHz at 500 kHz 10 Preliminary specification BGB100 MIN. TYP. MAX. UNIT −10 − − dBm −27 − − dBm − ...
Page 11
... Philips Semiconductors 0 dBm TrueBlue radio module TIMING DIAGRAMS S_DATA S_CLK S_EN 3-wire serial bus timing S_CLK/DATA REFCLK t1 S_EN t3 t4 T_GFSK t8 R_DATA DCXCTR 2002 Jan 03 32 clock cycles TX packet Fig.3 Timing diagram. 11 Preliminary specification packet t10 t12 t11 BGB100 t7 ...
Page 12
... The DCXCTR signal should go low at the actual end of the trailer sequence. The timing for this transition should be directly derived from the Acess Code detection algorithm inside the baseband processor. 2002 Jan 03 CONDITIONS note 1 note 2 note 3 note 4 note 5 12 Preliminary specification BGB100 MIN. TYP. UNIT − µs 0.1 − µs 2 − ...
Page 13
... Acetone. Ultrasonic cleaning should not be used since this can cause serious damage to the product. 2002 Jan 03 300 handbook, halfpage T (°C) 200 100 Fig.5 Recommended reflow temperature profile. Packing An extended packing / SMD specification can be found in document RNR-T49D-2183. 13 Preliminary specification BGB100 MGM159 (min) ...
Page 14
... Philips Semiconductors 0 dBm TrueBlue radio module PACKAGE OUTLINE 2002 Jan Fig Preliminary specification BGB100 SOT649A ...
Page 15
... Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. 15 Preliminary specification BGB100 DEFINITIONS ...
Page 16
... Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2001 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. ...