TDA4665 Philips Semiconductors, TDA4665 Datasheet
TDA4665
Available stocks
Related parts for TDA4665
TDA4665 Summary of contents
Page 1
... DATA SHEET TDA4665 Baseband delay line Product specification Supersedes data of 1995 Oct 30 File under Integrated Circuits, IC02 INTEGRATED CIRCUITS 1996 Dec 17 ...
Page 2
... TDA4665T SO16 plastic small outline package; 16 leads; body width 3.9 mm 1996 Dec 17 GENERAL DESCRIPTION The TDA4665 is an integrated baseband delay line circuit with one line delay suitable for decoders with colour-difference signal outputs (R Y) and (B Y). PARAMETER PACKAGE DESCRIPTION 2 Product specifi ...
Page 3
... Philips Semiconductors Baseband delay line BLOCK DIAGRAM 1996 Dec 17 3 Product specification TDA4665 ...
Page 4
... Dec 17 DESCRIPTION handbook, halfpage PARAMETER PARAMETER n.c. 2 GND2 3 i.c. 4 TDA4665 SAND 5 6 n.c. 7 i.c. 8 i.c. MED849 Fig.2 Pin configuration. MIN. 0.5 0.5 0.5 0 series resistor. VALUE 75 220 Product specification TDA4665 GND1 MAX. UNIT + 1 +150 500 V UNIT ...
Page 5
... V P all standards all standards V = 1.33 V i(14,16)(p-p) proportional ratio ratio 1.33 V; i(14,16)(p-p) SECAM signals note 2 i(14,16 active i(14,16) video 300 note 2 o(p-p) 5 Product specification TDA4665 MIN. TYP. MAX. UNIT 4 4 4.8 6.0 mA 0.7 1.0 mA 525 mV 665 mV 1. ...
Page 6
... For SECAM the signal must be blanked line-sequentially. The blanking level must be equal to the non-colour signal. For SECAM, PAL and NTSC the input signal must be equal to the non-colour signal during the internal clamping of TDA4665 ( before the leading edge of the top pulse Noise voltage kHz to 1 MHz ...
Page 7
... Philips Semiconductors Baseband delay line APPLICATION INFORMATION 1996 Dec 17 7 Product specification TDA4665 ...
Page 8
... REFERENCES JEDEC EIAJ ( 6.48 3.60 8.25 2.54 7.62 6.20 3.05 7.80 0.26 0.14 0.32 0.10 0.30 0.24 0.12 0.31 EUROPEAN PROJECTION Product specification TDA4665 SOT38-4 ( max. 10.0 0.254 0.76 8.3 0.39 0.01 0.030 0.33 ISSUE DATE 92-11-17 95-01-14 ...
Page 9
... REFERENCES JEDEC EIAJ MS-012AC detail 6.2 1.0 0.7 1.05 0.25 0.25 5.8 0.4 0.6 0.24 0.039 0.028 0.041 0.01 0.01 0.23 0.016 0.020 EUROPEAN PROJECTION Product specification TDA4665 SOT109 ( 0.7 0.1 0 0.028 0.004 0.012 ISSUE DATE 91-08-13 95-01-23 ...
Page 10
... Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 10 Product specification TDA4665 ...
Page 11
... Philips customers using or selling these products for use in such applications their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1996 Dec 17 11 Product specification TDA4665 ...
Page 12
... Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381 Middle East: see Italy For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. + 24825 © Philips Electronics N.V. 1996 All rights are reserved ...