SAA4995WP Philips Semiconductors, SAA4995WP Datasheet
SAA4995WP
Available stocks
Related parts for SAA4995WP
SAA4995WP Summary of contents
Page 1
... DATA SHEET SAA4995WP PANorama-IC (PAN-IC) Preliminary specification File under Integrated Circuits, IC02 INTEGRATED CIRCUITS 1997 Jun 10 ...
Page 2
... To achieve this a clock rate at twice the normal output clock rate is needed to write data to the memory. All actions to generate a lower data rate, produces disable cycles in Write Enable (WE). PARAMETER PACKAGE DESCRIPTION plastic leaded chip carrier; 44 leads 2 Preliminary specification SAA4995WP MIN. TYP. MAX. 4.5 5 5.5 110 33 0 ...
Page 3
... Jun 10 V DD1 V DD2 GND1 GND2 SECAM MUX NOTCH FRONT-END CLK notch FRONT-END SAA4995WP CLK MUX INTEGRATOR INTEGRATOR LINE CONTROL SNERT BUS INTERFACE Fig.1 Block diagram. 3 Preliminary specification SAA4995WP V DD3 V DD4 GND3 GND4 VPD VPD BACK-END VPD VPD BACK-END UV Y DTO ...
Page 4
... DD3 SNDA SNCL VRST Preliminary specification SAA4995WP PIN DESCRIPTION 24 luminance output bit 2 25 luminance output bit 3 26 luminance output bit 4 27 luminance output bit 5 28 luminance output bit 6 29 luminance output bit 7 30 ground 3 31 system clock 32 ground 4 33 supply voltage 3 ...
Page 5
... II and V) X programmed for its 2nd derivative (for areas III and IV) X stream, defined by start stream, defined by the programmed number of samples C rate in areas II and V C rate in areas III and IV. 5 Preliminary specification SAA4995WP VRST 35 SNCL 34 SDNA V DD3 ...
Page 6
... The PAN-IC usually delivers a complete YUV data stream to one receiving device, e.g. a field memory. Optionally, a data stream can be split into odd and even samples received by two receiving devices. The relationship between Y and UV samples is then non-trivial (see Tables 1 to 4). 6 Preliminary specification SAA4995WP (programmed (programmed ...
Page 7
... A separate input signal for each of the receiving devices must then be applied while the even YUV data stream and odd YUV data stream are again combined YUV OMBINED ODD EVEN OUTPUT Table 4 Distribution with odd/even input enable signals 1997 Jun DATA STREAM Preliminary specification SAA4995WP etc. in even stream and ...
Page 8
... Philips Semiconductors PANorama-IC (PAN-IC) handbook, full pagewidth area: IV sample C 2 rate X 1I positions handbook, full pagewidth 1997 Jun 10 active period Fig.3 Panorama mode. 2 compress factor 1 0.5 256 128 0 DTO incr Fig.4 Compress factor. 8 Preliminary specification SAA4995WP II III MGK177 MGK178 256 X 2r ...
Page 9
... Machine model 200 pF 300 V. THERMAL CHARACTERISTICS SYMBOL R thermal resistance from junction to ambient in free air th j-a 1997 Jun 10 Fig.5 WE timing. CONDITIONS note 1 note 2 PARAMETER 9 Preliminary specification SAA4995WP with in-phase = 0 with in-phase = 1 with out-phase = 0 with out-phase = 1 MGK179 MIN. MAX. UNIT 0.5 +6 ...
Page 10
... VRST and CLK; see Fig.6 except pins SNDA, SNCL, VRST and CLK; see Fig.6 see Fig.6 see Fig h(i)(CL16) t su(i)(CL16) t h(i)(D) data valid t h( Fig.6 Clock timing. 10 Preliminary specification SAA4995WP MIN. TYP. MAX. 4.5 5 5.5 110 CLK 0.8 2 0.4 2 ...
Page 11
... X note definition of X note definition of X note resolution of 4 luminance samples; actual # samples = (programmed # samples + 1) 11 Preliminary specification SAA4995WP CONDITIONS MIN cy(SNCL) data data data valid valid valid REMARKS with a resolution of 4 samples; see Fig.3 and 1l with a resolution of 4 samples; see Fig.3 and 0l with a resolution of 4 samples ...
Page 12
... PAN-IC identifies by pulling all bits LOW (hardware cluck output samples per line + latest sample should not be equal to the pipeline delay. This can be controlled O 12 Preliminary specification SAA4995WP REMARKS value for area I, MSB extended by zoom bit incr for areas II and V incr for areas III and IV incr /WE to output data ...
Page 13
... Preliminary specification detail max. 17.65 17.65 1.22 1.44 0.51 0.18 0.18 17.40 17.40 1.07 1.02 0.695 0.695 0.048 0.057 0.020 0.007 0.007 0.004 0.685 0.685 0.042 0.040 EUROPEAN PROJECTION SAA4995WP SOT187 (1) ( max. max. 0.10 2.16 2. 0.085 0.085 ISSUE DATE 92-11-17 95-02-25 ...
Page 14
... Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 14 Preliminary specification SAA4995WP ...
Page 15
... Philips customers using or selling these products for use in such applications their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1997 Jun 10 15 Preliminary specification SAA4995WP ...
Page 16
... Tel. +46 8 632 2000, Fax. +46 8 632 2745 Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH, Tel. +41 1 488 2686, Fax. +41 1 481 7730 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel ...