MAX709L Maxim Integrated Products, MAX709L Datasheet
MAX709L
Available stocks
Related parts for MAX709L
MAX709L Summary of contents
Page 1
... SUFFIX __________________Pin Configuration TOP VIEW N. GND N.C. Transients CC 65µA - MAX709L/M TEMP. RANGE PIN-PACKAGE 0°C to +70°C 8 Plastic DIP 0°C to +70°C 8 µMAX 0°C to +70° 0°C to +70°C Dice -40°C to +85°C 8 Plastic DIP -40°C to +85°C 8 µMAX -40°C to +85° +25 ° ...
Page 2
... V SINK RESET Output Voltage I = 100µA, V SINK I SOURCE MAX709R/S/T only I SOURCE MAX709L/M only Note 1: Supply current is measured with _______________________________________________________________________________________ Operating Temperature Ranges MAX709_C___ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C + 0.3V) MAX709_E___ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C CC Storage Temperature Range . . . . . . . . . . . . . . . . . . - 65°C to +160°C Lead Temperature (soldering, 10sec +300°C ...
Page 3
Power-Supply Monitor with Reset __________________________________________Typical Operating Characteristics POWER-UP RESET DELAY vs. TEMPERATURE 300 V = RESET THRESHOLD MAX RISING CC 250 200 150 100 50 0 -60 -20 20 TEMPERATURE (°C) SUPPLY CURRENT vs. TEMPERATURE 100 NOTE: STEADY-STATE ...
Page 4
... As the magnitude of the transient increases (goes farther below the reset threshold), the maximum allowable pulse width decreases. Typically, for the MAX709L/MAX709M transient that goes 100mV CC below the reset threshold and lasts 40µs or less will not cause a reset pulse to be issued. ...
Page 5
Power-Supply Monitor with Reset V CC MAX709 RESET R1 GND Figure 2. RESET Valid Ground Circuit CC Interfacing to µPs with Bidirectional Reset Pins Microprocessors with bidirectional reset pins (such as the Motorola 68HC11 series) can contend ...
Page 6
... MAX705/706 4.65/4.40 140 1.6 MAX706P 2.63 140 1.6 MAX706R/S/T 2.63/2.93/ 140 1.6 3.08 MAX707/708 4.65/4.40 140 - MAX708R/S/T 2.63/2.93/ 140 - 3.08 MAX709L/M/ 4.65/4.40/ 140 - R/S/T 2.63/2.93/3.08 MAX791 4.65 140 1 MAX792L/M/ 4.65/4.40/ 140 1 R/S/T 2.63/2.93/3.08 MAX800L/M 4.60/4.40 140 1.6/adj. MAX802L/M 4.60/4.40 140 1.6 MAX805L 4 ...
Page 7
Power-Supply Monitor with Reset ___________________Chip Topography V CC RESET GND 0.056" (1.422mm) TRANSISTOR COUNT: 380 SUBSTRATE CONNECTED ________________________________________________________Package Information A 0.101mm 0.004 _______________________________________________________________________________________ 0.045" (1.143mm 8-PIN MAX MICROMAX ...
Page 8
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 8 ___________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 © 1994 Maxim Integrated Products 0° ...