V300A15C500BN Vicor Corporation, V300A15C500BN Datasheet
V300A15C500BN
Related parts for V300A15C500BN
V300A15C500BN Summary of contents
Page 1
RoHS Compliant (with pin option) DC input range: 180 – 375 V Input surge withstand: 400 V for 100 ms DC output: 2 – Programmable output 110% Regulation: ±0.3% no load to full ...
Page 2
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature, unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate. Operating input voltage 180 Input surge withstand ...
Page 3
Primary Control Parallel) PC bias voltage 5.50 current limit 1.5 PC module disable 2.3 PC module enable delay PC module alarm PR emitter amplitude 5.7 PR emitter current 150 PR receiver impedance 375 PR receiver threshold ...
Page 4
Efficiency 72.5 Ripple and noise Output OVP setpoint 2.7 Dissipation, standby Load regulation Load current 0 Current limit 81.6 Short circuit current 56 Efficiency 79 Ripple and noise Output OVP setpoint 4.14 Dissipation, standby Load regulation Load current 0 Current ...
Page 5
Efficiency 82 Ripple and noise Output OVP setpoint 9.36 Dissipation, standby Load regulation Load current 0 Current limit 51 Short circuit current 35 Efficiency 82 Ripple and noise Output OVP setpoint 9.36 Dissipation, standby Load regulation Output Current 0 Current ...
Page 6
Efficiency 81.4 Ripple and noise Output OVP setpoint 17.1 Dissipation, standby Load regulation Load current 0 Current limit 27.2 Short circuit current 18.6 Efficiency 87 Ripple and noise Output OVP setpoint 27.1 Dissipation, standby Load regulation Load current 0 Current ...
Page 7
Efficiency 87 Ripple and noise Output OVP setpoint 40.4 Dissipation, standby Load regulation Load current 0 Current limit 14.1 Short circuit current 9.73 Efficiency 87 Ripple and noise Output OVP setpoint 40.4 Dissipation, standby Load regulation Load current 0 Current ...
Page 8
The module may be disabled by pulling PC below 2.3 V with respect to the –Input. This may be done with an open collector transistor, relay, or optocoupler. Multiple converters may be disabled with a single transistor or relay either ...
Page 9
The output voltage of the converter can be adjusted or programmed via fixed resistors, potentiometers or voltage DACs. See Figures 7 and 8. +OUT +S Error SC Amp –S 0.033 μF 1 kΩ –OUT 1.23 V 1,000 Vout R (ohms) ...
Page 10
The PR pin supports paralleling for increased power with N+1 (N+M) redundancy and phased array capability. Modules of the same input voltage, output voltage, and power level will current share if all PR pins are suitably interfaced. Compatible interface architectures ...
Page 11
Module 1 SC –S –S –OUT +S +OUT +S +S Module 2 SC Load –S –S –OUT –S +OUT +S Module N+1 SC –S –OUT Figure 11 — N+1 module array output connections. (None) Short Tin/Lead L ...
Page 12
No. Function Label 0.300±0.015 1 +In + 7,62±0,38 0.23 Primary 5 Control 3 Parallel PR 0.300±0.015 7,62±0,38 4 –In – 5 –Out – 6 –Sense –S Secondary 7 SC Control 8 +Sense +S 9 +Out + Slotted or ...
Page 13
Vicor products are guaranteed for two years from date of shipment against defects in material or workmanship when in normal use and service. This warranty does not extend to products subjected to misuse, accident, or improper application or maintenance. Vicor ...