V48C2C50B Vicor Corporation, V48C2C50B Datasheet
V48C2C50B
Available stocks
Related parts for V48C2C50B
V48C2C50B Summary of contents
Page 1
RoHS Compliant (with pin option) • DC input range • Input surge withstand: 100 V for 100 ms • DC output: 2 – • Programmable output 110% • ...
Page 2
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature, unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate. MODULE INPUT SPECIFICATIONS Parameter Min Operating input ...
Page 3
MODULE CONTROL SPECIFICATIONS Parameter Min PRIMARY SIDE (PC = Primary Control Parallel) PC bias voltage 5.50 current limit 1.5 PC module disable 2.3 PC module enable delay PC module alarm PR emitter amplitude 5.7 PR emitter current 150 ...
Page 4
... MODULE SPECIFIC OPERATING SPECIFICATIONS 2 Vout (e.g. V48C2C50BL) Parameter Min Efficiency 76 Ripple and noise Output OVP setpoint 2.7 Dissipation, standby Load regulation Load current 0 Current limit 25.3 Short circuit current 17.5 3.3 Vout (e.g. V48C3V3C75BL) Parameter Min Efficiency 80.5 Ripple and noise Output OVP setpoint 4 ...
Page 5
MODULE SPECIFIC OPERATING SPECIFICATIONS (CONT.) 5 Vout (e.g. V48C5C50BL) Parameter Min Efficiency 83.5 Ripple and noise Output OVP setpoint 6.03 Dissipation, standby Load regulation Load current 0 Current limit 10.2 Short circuit current 7 12 Vout, 150 W ...
Page 6
MODULE SPECIFIC OPERATING SPECIFICATIONS (CONT.) 24 Vout, 150 W (e.g. V48C24C150BL) Parameter Min Efficiency 87.5 Ripple and noise Output OVP setpoint 27.1 Dissipation, standby Load regulation Load current 0 Current limit 6.37 Short circuit current 4.06 24 Vout ...
Page 7
MODULE SPECIFIC OPERATING SPECIFICATIONS (CONT.) 48 Vout, 150 W (e.g. V48C48C150BL) Parameter Min Efficiency 88 Ripple and noise Output OVP setpoint 53.7 Dissipation, standby Load regulation Load current 0 Current limit 3.19 Short circuit current 2.19 48 Vout ...
Page 8
The module may be disabled by pulling PC below 2.3 V with respect to the –Input. This may be done with an open collector transistor, relay, or optocoupler. Multiple converters may be disabled with a single transistor or relay either ...
Page 9
The output voltage of the converter can be adjusted or programmed via fixed resistors, potentiometers or voltage DACs. See Figures 7 and 8. +OUT Error SC Amp 0.033 μF 1 kΩ –OUT 1.23 V 1,000 Vout R (ohms ...
Page 10
The PR pin supports paralleling for increased power with N+1 (N+M) redundancy and phased array capability. Modules of the same input voltage, output voltage, and power level will current share if all PR pins are suitably interfaced. Compatible interface architectures ...
Page 11
Plane Module #1 SC Designated Master –OUT +OUT Module # trimmed A D down 2 % –OUT +OUT Module #3 trimmed SC Ground down 4 % Plane –OUT Figure 11 — N+1 module array output connections. ...
Page 12
Converter Pins No. Function Label 1 +In + Primary 2 PC Control 3 Parallel PR 0.235±.015 4 –In – 5,97±0,38 (REF) 5 –Out – Secondary Pin Control 7 +Out + 0.350±.015 8,89±0,38 (REF) Slotted 0.21 5,2 ...
Page 13
Vicor products are guaranteed for two years from date of shipment against defects in material or workmanship when in normal use and service. This warranty does not extend to products subjected to misuse, accident, or improper application or maintenance. Vicor ...