MAX9719AETE+ Maxim Integrated Products, MAX9719AETE+ Datasheet - Page 10

IC AMP AUDIO PWR 1.4W AB 16TQFN

MAX9719AETE+

Manufacturer Part Number
MAX9719AETE+
Description
IC AMP AUDIO PWR 1.4W AB 16TQFN
Manufacturer
Maxim Integrated Products
Type
Class ABr
Datasheet

Specifications of MAX9719AETE+

Output Type
2-Channel (Stereo)
Max Output Power X Channels @ Load
1.4W x 2 @ 4 Ohm
Voltage - Supply
2.7 V ~ 5.5 V
Features
Depop, Differential Inputs, Shutdown, Thermal Protection
Mounting Type
Surface Mount
Package / Case
16-TQFN Exposed Pad
Product
Class-AB
Output Power
1.4 W
Common Mode Rejection Ratio (min)
- 60 dB
Thd Plus Noise
0.002 %
Operating Supply Voltage
2.7 V to 5.5 V
Supply Current
5 mA
Maximum Power Dissipation
1349 mW
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Input Signal Type
Differential
Minimum Operating Temperature
- 40 C
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
Q2749818A
Low-Cost, Mono/Stereo,
1.4W Differential Audio Power Amplifiers
The MAX9718/MAX9719 are 1.4W BTL speaker ampli-
fiers. The MAX9718 is a mono speaker amplifier, while
the MAX9719 is a stereo speaker amplifier. Both
devices feature a low-power shutdown mode and indus-
try-leading click-and-pop suppression. The MAX9718
features a two-input shutdown scheme to configure
shutdown for active high or active low. These devices
consist of high output-current audio amps configured as
BTL amplifiers (see the Functional Diagrams ). Both
adjustable and fixed gain (0dB, 3dB, 6dB) versions are
available.
These devices operate from a single 2.7V to 5.5V sup-
ply and feature an internally generated, common-mode
bias voltage of V
vides both click-and-pop suppression and sets the DC
bias level for the audio outputs. Choose the value of the
bypass capacitor as described in the BIAS Capacitor
section. Do not connect external loads to BIAS as this
can affect the overall performance.
The MAX9718/MAX9719 feature a 100nA low-power
shutdown mode that reduces quiescent current con-
sumption. Entering shutdown disables the device’s bias
circuitry, the amplifier outputs go high impedance, and
BIAS is driven to GND. The MAX9718 SHDM input con-
trols the polarity of SHDN. Drive SHDM high for an
active-high SHDN input. Drive SHDM low for an active-
low SHDN input (see Table 1). The MAX9719 features
an active-low shutdown input, SHDN.
The MAX9718/MAX9719 feature Maxim’s industry-lead-
ing click-and-pop suppression circuitry. During startup,
the amplifier common-mode bias voltage ramps to the
DC bias point. When entering shutdown, the amplifier
outputs are high impedance to 100kΩ between both
outputs. This scheme minimizes the energy present in
the audio band.
10
TDFN-EP/
µMAX
______________________________________________________________________________________
UCSP
CC
/2 referenced to ground. BIAS pro-
Click-and-Pop Suppression
Detailed Description
TQFN-EP
PIN
10
12
15
16
UCSP
Shutdown Mode
D4
D2
D1
B4
TSSOP-EP
12
14
1
2
BIAS
OUTR+
OUTR-
NAME
OUTL-
INR-
EP
The MAX9718/MAX9719 are designed to drive a load
differentially, a configuration referred to as bridge-tied
load or BTL. The BTL configuration (Figure 1) offers
advantages over the single-ended configuration, where
one side of the load is connected to ground. Driving the
load differentially doubles the output voltage compared
to a single-ended amplifier under similar conditions.
Substituting 2 x V
equations yields four times the output power due to
doubling of the output voltage:
Since the differential outputs are biased at midsupply,
there is no net DC voltage across the load. This elimi-
nates the need for DC-blocking capacitors required for
single-ended amplifiers. These capacitors can be
large, expensive, consume board space, and degrade
low-frequency performance.
Table 1. Shutdown Mode Selection
(MAX9718 Only)
Left-Channel Bridge Amplifier Negative Output
Right-Channel Bridge Amplifier Positive Output
Right-Channel Bridge Amplifier Negative Output
Right-Channel Inverting Input
Exposed Pad. Connect EP to GND.
SHDM
0
0
1
1
Pin Description (continued)
Applications Information
OUT(P-P)
SHDN
V
0
1
0
1
RMS
P
OUT
FUNCTION
=
=
for V
V
V
OUT P P
RMS
2 2
R
OUT(P-P)
OPERATIONAL MODE
L
(
2
Normal operation
Normal operation
)
Shutdown
Shutdown
BTL Amplifier
into the following

Related parts for MAX9719AETE+