MAX9724AETC+ Maxim Integrated Products, MAX9724AETC+ Datasheet - Page 11

• Manufacturer Part Number: MAX9724AETC+
• Description: IC AMP AUDIO .045W STER 12TQFN
• Manufacturer: Maxim Integrated Products
• Series: DirectDrive™r
• Type: Class ABr

Specifications of MAX9724AETC+

• Output Type: Headphones, 2-Channel (Stereo)
• Max Output Power X Channels @ Load: 63mW x 2 @ 32 Ohm
• Voltage - Supply: 2.7 V ~ 5.5 V
• Features: Depop, Short-Circuit and Thermal Protection, Shutdown
• Mounting Type: Surface Mount
• Package / Case: 12-TQFN Exposed Pad
• Product: General Purpose Audio Amplifiers
• Output Power: 42 mW
• Thd Plus Noise: 0.02 %
• Supply Current: 3.5 mA
• Maximum Power Dissipation: 1333 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Audio Load Resistance: 16 Ohms
• Minimum Operating Temperature: - 40 C
• Amplifier Class: AB
• No. Of Channels: 2
• Supply Voltage Range: 2.7V To 5.5V
• Load Impedance: 16ohm
• Operating Temperature Range: -40°C To +85°C
• Amplifier Case Style: TQFN
• Rohs Compliant: Yes
• For Use With: MAX9724AEVKIT+ - EVALUATION KIT FOR MAX9724A/BMAX9724DEVKIT+ - KIT EVAL FOR MAX9724D
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

°C/W as specified in the Absolute Maximum Ratings
section. For example, θ
+68°C/W, and 154.2°C/W for the UCSP package.
The MAX9724A/MAX9724B have two power dissipation
sources; a charge pump and the two output amplifiers.
If power dissipation for a given application exceeds the
maximum allowed for a particular package, reduce
V
temperature, or add heatsinking to the device. Large
output, supply, and ground traces decrease θ
ing more heat to be transferred from the package to the
surrounding air.
Thermal-overload protection limits total power dissipa-
tion in the MAX9724A/MAX9724B. When the junction
temperature exceeds +150°C, the thermal protection
circuitry disables the amplifier output stage. The ampli-
fiers are enabled once the junction temperature cools
by approximately 12°C. This results in a pulsing output
under continuous thermal-overload conditions.
Dynamic range is the difference between the noise floor
of the system and the output level at 1% THD+N.
Determine the system’s dynamic range before setting the
maximum output gain. Output clipping occurs if the out-
put signal is greater than the dynamic range of the sys-
tem. The DirectDrive architecture of the MAX9724A/
MAX9724B has increased the dynamic range compared
to other single-supply amplifiers.
If the output load impedance is greater than 1kΩ, the
MAX9724A/MAX9724B can swing within a few millivolts
of their supply rail. For example, with a 3.3V supply, the
output swing is 2V
a low 0.003% THD+N. If the supply voltage drops to
3V, the same 2.83V peak has only 0.05% THD+N.
Internal device structures limit the maximum voltage
swing of the MAX9724A/MAX9724B when operated at
supply voltages greater than 4.35V. The output must not
be driven such that the peak output voltage exceeds the
Table 2. Suggested Capacitor Manufacturers
DD
Taiyo Yuden
TDK
Murata
60mW, DirectDrive, Stereo Headphone Amplifier
, increase load impedance, decrease the ambient
SUPPLIER
with Low RF Susceptibility and Shutdown
RMS
______________________________________________________________________________________
, or 2.83V peak while maintaining
JA
Maximum Output Swing
Output Dynamic Range
of the thin QFN package is
800-348-2496
847-803-6100
770-436-1300
V
V
PHONE
DD
DD
JA
< 4.35V
> 4.35V
, allow-
opposite supply voltage by 9V. For example, if V
5V, the charge pump sets PV
peak output swing must be less than ±4V to prevent
exceeding the absolute maximum ratings.
The MAX9724A/MAX9724B feature an undervoltage
lockout (UVLO) function that prevents the device from
operating if the supply voltage is less than 2.7V. This fea-
ture ensures proper operation during brownout condi-
tions and prevents deep battery discharge. Once the
supply voltage exceeds the UVLO threshold, the
MAX9724A/MAX9724B charge pump is turned on and
the amplifiers are powered, provided that SHDN is high.
The input capacitor (C
resistor (R
DC bias from an incoming signal (see the Functional
Diagram/Typical Operating Circuits ). The AC-coupling
capacitor allows the device to bias the signal to an opti-
mum DC level. Assuming zero-source impedance, the -
3dB point of the highpass filter is given by:
Choose the C
frequency of interest. Setting f
device’s low-frequency response. Use capacitors
whose dielectrics have low-voltage coefficients, such
as tantalum or aluminum electrolytic. Capacitors with
high-voltage coefficients, such as ceramics, can result
in increased distortion at low frequencies.
Use ceramic capacitors with a low ESR for optimum
performance. For optimal performance over the extend-
ed temperature range, select capacitors with an X7R
dielectric. Table 2 lists suggested manufacturers.
The value of the flying capacitor (see the Functional
Diagram/Typical Operating Circuits ) affects the charge
847-925-0899
847-390-4405
770-436-3030
IN
FAX
), forms a highpass filter that removes the
IN
such that f
f
−
Charge-Pump Capacitor Selection
3
dB
IN
=
), in conjunction with the input
2π
-3dB
Component Selection
Input-Coupling Capacitor
R C
IN IN
1
www.component.tdk.com
SS
-3dB
is well below the lowest
Flying Capacitor (C1)
www.t-yuden.com
= -5V. Therefore, the
www.murata.com
too high affects the
WEBSITE
UVLO
DD
11
=