MCP2200-I/SO Microchip Technology, MCP2200-I/SO Datasheet - Page 5

• Manufacturer Part Number: MCP2200-I/SO
• Description: IC USB TO UART 20SOIC
• Manufacturer: Microchip Technology
• Type: USB to UART Protocol Converterr

Specifications of MCP2200-I/SO

• Package / Case: 20-SOIC (0.300", 7.50mm Width)
• Features: USB to UART
• Number Of Channels: 8
• Fifo's: 256 Byte
• Protocol: USB 2.0
• Voltage - Supply: 3 V ~ 5.5 V
• With Auto Flow Control: Yes
• Mounting Type: Surface Mount
• Mounting Style: SMD/SMT
• Operating Temperature Range: - 40 C to + 85 C
• Supply Current: 13 mA
• Operating Supply Voltage: 3 V to 5.5 V
• Usb Version: 2.0
• Data Rate: 12Mbps
• Supply Voltage Range: 3V To 5.5V
• Digital Ic Case Style: SOIC
• No. Of Pins: 20
• Peak Reflow Compatible (260 C): Yes
• Rohs Compliant: Yes
• Leaded Process Compatible: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

1.3.4
Hardware flow control uses the RTS and CTS pins as
a handshake between two devices. The RTS pin of
one device is typically connected to the CTS of the
other device.
RTS is an active low output which notifies the other
device when it can receive data by driving the pin low.
The MCP2200 trip point for de-asserting RTS (high) is
63 characters. This is one character short of “buffer
full”.
CTS is an active low input which is used to notify the
MCP2200 when it can send data. The MCP2200 will
check CTS just before loading and sending UART data.
If the pin is asserted during a transfer, the transfer will
continue. Refer to
1.3.4.1
The buffer pointer does not increment (or reset to
zero) if the buffer is full. Therefore, if hardware flow
control is not enabled and an overflow occurs (i.e., 65
unprocessed characters received), the new data over-
writes the last position in the buffer.
FIGURE 1-1:
EQUATION 1-1:
 2010 Microchip Technology Inc.
I am ready
to receive
I’ll transmit
if okay
Where:
HARDWARE FLOW CONTROL
RTS
MCU
CTS
Flow Control Disabled
ActualRate
x
=
Figure
---------------------------------- -
DesiredBaud
RTS/CTS CONNECTIONS
EXAMPLE
SOLVING FOR ACTUAL
BAUD RATE
12MHz
1-1.
=
12MHz
------------------
int x  
MCP2200
RTS
CTS
I am ready
to receive
I’ll transmit
if okay
TABLE 1-3:
1.4
The USB controller in the MCP2200 is full-speed USB
2.0 compliant.
• Composite device (CDC + HID):
• 128 byte buffer to handle data throughput at any
• Fully configurable VID and PID assignments, and
• Bus powered or self-powered
1.4.1
The descriptors are stored in the MCP2200 during
configuration using the supplied PC interface.
1.4.2
The USB Suspend and Resume signals are supported
for power management of the MCP2200. The device
will enter Suspend mode when suspend signaling is
detected on the bus.
The MCP2200 exits the Suspend mode when any of
the following occur:
1.
2.
3.
300
1200
2400
4800
9600
19200
38400
57600
115200
230400
460800
921600
Desired Rate
- CDC: USB-to-UART communications
- HID: I/O control, EEPROM access and initial
UART baud rate:
- 64 byte transmit
- 64 byte receive
descriptors (stored on-chip)
configuration
Resume signaling is detected or generated
A USB Reset signal is detected
A device Reset occurs
USB Protocol Controller
DESCRIPTORS
SUSPEND AND RESUME
UART PRIMARY BAUD
RATES
Actual rate
230769
461538
923077
115385
19200
38339
57692
1200
2400
4800
9600
300
MCP2200
DS22228A-page 5
% Error
0.00%
0.00%
0.00%
0.00%
0.00%
0.00%
0.16%
0.16%
0.16%
0.16%
0.16%
0.16%