MAX3110ECNI+G36 Maxim Integrated Products, MAX3110ECNI+G36 Datasheet - Page 21
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX3110ECNI+G36
Manufacturer Part Number
MAX3110ECNI+G36
Description
IC TXRX RS232 SPI W/CAP 28-DIP
Manufacturer
Maxim Integrated Products
Type
SPI/MICROWIRE-Compatible UART with Integrated ESD-Protected RS-232 Transceiverr
Datasheet
1.MAX3110ECWIG36.pdf
(31 pages)
Specifications of MAX3110ECNI+G36
Features
Transceiver
Number Of Channels
1, UART
Protocol
RS232, RS485
Voltage - Supply
4.5 V ~ 5.5 V
With Irda Encoder/decoder
Yes
With False Start Bit Detection
Yes
With Cmos
Yes
Mounting Type
Through Hole
Package / Case
28-DIP (0.300", 7.62mm)
Data Rate
250 Kbps
Supply Voltage (max)
5.5 V
Supply Voltage (min)
4.5 V
Supply Current
0.6 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Description/function
SPI/MICROWIRE-Compatible UART with integrated ESD-protected RS-232 transceiver
Mounting Style
Through Hole
Operating Supply Voltage
5 V
Propagation Delay Time Ns
150 ns
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 7. Interrupt Sources and Masks—Bit Descriptions
When in software shutdown, the UART’s oscillator turns
off to reduce power dissipation. The UART enters shut-
down by a software command (SHDNi bit = 1). The
software shutdown is entered upon completing the
transmission of the data in both the Transmit register
and the Transmit-Buffer register. The SHDNo bit is set
when the UART enters shutdown. The microcontroller
(µC) monitors the SHDNo bit to determine when the
UART is shut down and then shuts down the
RS-232 transceivers.
Software shutdown clears the receive FIFO, R, RA/FE,
D0r–D7r, Pr, and Pt registers and sets the T bit high.
Configuration bits (RM, TM, PM, RAM, IR, ST, PE, L,
B0–B3, and RTS) are programmable when SHDNo = 1
and CTS is also readable. Although RA is reset upon
entering shutdown, it goes high when any transitions
are detected on the RX pin. This allows the UART to
monitor activity on the receiver when in shutdown.
When taking the part out of software shutdown (SHDNi
= 0), the oscillator turns on when CS goes high. After
Protected RS-232 Transceivers with Internal Capacitors
NAME
RA/FE
BIT
Pr
R
T
SPI/MICROWIRE-Compatible UART and ±15kV ESD-
MASK
RAM
BIT
RM
PM
TM
______________________________________________________________________________________
Received parity bit = 1
Data available
Transition on RX when
in shutdown; framing
error when not in
shutdown
Transmit buffer is
empty
WHEN SET
MEANING
UART Software Shutdown
The Pr bit reflects the value in the word currently in the receive-buffer register
(oldest data available). The Pr bit is set when parity is enabled (PE = 1) and the
received parity bit is 1. The Pr bit is cleared either when parity is not enabled (PE
= 0) or when parity is enabled and the received bit is 0. An interrupt is issued
based on the oldest Pr value in the receiver FIFO. The oldest Pr value is the next
value read by a Read Data operation.
The R bit is set when new data is available to be read or when data is being read
from the receive register/FIFO. FIFO is cleared when all data has been read. An
interrupt is asserted as long as R = 1 and RM = 1.
This is the RA (RX-transition) bit in shutdown, and the framing-error (FE) bit in
operating mode. RA is set if there has been a transition on RX since entering
shutdown. RA is cleared when the MAX3110E/MAX3111E exits shutdown. IRQ is
asserted when RA is set and RAM = 1.
FE is determined solely by the currently received data and is not stored in FIFO.
The FE bit is set if a zero is received when the first stop bit is expected. FE is
cleared upon receipt of the next properly framed character. IRQ is asserted
when FE is set and RAM = 1.
The T bit is set when the transmit buffer is ready to accept data. IRQ is asserted
low if TM = 1 and the transmit buffer becomes empty. This source is cleared on
the rising edge of SCLK’s 16th clock pulse when using a Read Data or Write
Data operation. CS’s rising edge during a Read Data operation. Although the
interrupt is cleared, poll T to determine transmit-buffer status.
CS goes high, the oscillator typically takes about 25ms
to stabilize. Configure the UART after the oscillator has
stabilized by using a write configuration that clears all
registers but RTS and CTS. If a framing error occurs,
you may have not waited long enough for the oscillator
to stabilize.
The hardware shutdown affects only the RS-232 trans-
ceiver, and the software shutdown affects only the
UART. See the RS-232 Transceiver Hardware
Shutdown section.
The internal power supply consists of a regulated dual
charge pump that provides output voltages of +5.5V
(doubling charge pump) and -5.5V (inverting charge
pump), using a +3.3V supply (MAX3111E) or a +5V sup-
ply (MAX3110E). The charge pump operates in discontin-
uous mode; if the output voltages are less than 5.5V, the
charge pump is enabled, and if the output voltages
exceed 5.5V, the charge pump is disabled. Each charge
pump includes internal flying capacitors and reservoir
capacitors to generate the V+ and V- supplies.
Dual Charge-Pump Voltage Converter
DESCRIPTION
21