SI3215-KT Silicon Laboratories Inc, SI3215-KT Datasheet - Page 43
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
SI3215-KT
Manufacturer Part Number
SI3215-KT
Description
IC SLIC/CODEC 1CH 38TSSOP
Manufacturer
Silicon Laboratories Inc
Series
ProSLIC®r
Datasheet
1.SI3215-B-FM.pdf
(118 pages)
Specifications of SI3215-KT
Function
Subscriber Line Interface Concept (SLIC), CODEC
Interface
PCM, SPI
Number Of Circuits
1
Voltage - Supply
3.13 V ~ 5.25 V
Current - Supply
88mA
Power (watts)
700mW
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
*
Includes
Audio Tone Generation, BORSCHT Functions, FSK Generation, Voice Loopback Test Modes
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SI3215-KT
Manufacturer:
SILICONIX
Quantity:
20 000
2.9. Interrupt Logic
The ProSLIC is capable of generating interrupts for the
following events:
The interface to the interrupt logic consists of six
registers. Three interrupt status registers contain one bit
for each of the above interrupt functions. These bits will
be set when an interrupt is pending for the associated
resource. Three interrupt enable registers also contain
one bit for each interrupt function. In the case of the
interrupt enable registers, the bits are active high. Refer
to the appropriate functional description section for
operational details of the interrupt functions.
When a resource reaches an interrupt condition, it will
signal an interrupt to the interrupt control block. The
interrupt control block will then set the associated bit in
the interrupt status register if the enable bit for that
interrupt is set. The INT pin is a NOR of the bits of the
interrupt status registers. Therefore, if a bit in the
interrupt status registers is asserted, IRQ will assert low.
Upon receiving the interrupt, the interrupt handler
should read interrupt status registers to determine
which resource is requesting service. To clear a pending
interrupt, write the desired bit in the appropriate
interrupt status register to 1. Writing a 0 has no effect.
This provides a mechanism for clearing individual bits
when multiple interrupts occur simultaneously. While the
interrupt status registers are non-zero, the INT pin will
remain asserted.
2.10. Serial Peripheral Interface
The control interface to the ProSLIC is a 4-wire interface
modeled after commonly-available microcontroller and
serial peripheral devices. The interface consists of a
clock (SCLK), chip select (CS), serial data input (SDI),
and serial data output (SDO). Data is transferred a byte
at a time with each register access consisting of a pair
of byte transfers. Figures 24 and 25 illustrate read and
write operation in the SPI bus.
Loop current/ring ground detected
Ring trip detected
Power alarm
Active timer 1 expired
Inactive timer 1 expired
Active timer 2 expired
Inactive timer 2 expired
Ringing active timer expired
Ringing inactive timer expired
Pulse metering active timer expired
Pulse metering inactive timer expired
Indirect register access complete
Rev. 0.92
The first byte of the pair is the command/address byte.
The MSB of this byte indicates a register read when 1
and a register write when 0. The remaining seven bits of
the command/address byte indicate the address of the
register to be accessed. The second byte of the pair is
the data byte. Because the falling edge of CS provides
resynchronization of the SPI state machine in the event
of a framing error, it is recommended (but not required)
that CS be taken high between byte transfers as shown
in Figures 24 and 25. During a read operation, the SDO
becomes active, and the 8-bit contents of the register
are driven out MSB first. The SDO will be high
impedence on either the falling edge of SCLK following
the LSB or the rising of CS as specified by the SPIM bit
(direct Register 0, bit 6). SDI is a “don’t care” during the
data portion of read operations. During write operations,
data is driven into the ProSLIC via the SDI pin MSB first.
The SDO pin will remain high impedance during write
operations. Data always transitions with the falling edge
of the clock and is latched on the rising edge. The clock
should return to a logic high when no transfer is in
progress.
Indirect registers are accessed through direct registers
29 through 30. Instructions on how to access them are
presented in “3.Control Registers” beginning on page
50.
There are a number of variations of usage on this four-
wire interface:
Continuous clocking . During continuous clocking,
the data transfers are controlled by the assertion of
the CS pin. CS must assert before the falling edge of
SCLK on which the first bit of data is expected during
a read cycle, and must remain low for the duration of
the 8-‘bit transfer (command/address or data).
SDI/SDO wired operation. Independent of the
clocking options described, SDI and SDO can be
treated as two separate lines or wired together if the
master is capable of tristating its output during the
data byte transfer of a read operation.
Daisy chain mode. This mode allows
communication with banks of up to eight ProSLIC
devices using one chip select signal. When the
SPIDC bit in the SPI Mode Select register is set,
data transfer mode changes to a 3-byte operation: a
chip select byte, an address/control byte, and a data
byte. Using the circuit shown in Figure 26, a single
device may select from the bank of devices by
setting the appropriate chip select bit to 1. Each
device uses the LSB of the chip select byte, shifts
the data right by one bit, and passes the chip select
byte using the SDITHRU pin to the next device in the
chain. Address/control and data bytes are unaltered.
Si3215
43