SI3220-BQ Silicon Laboratories Inc, SI3220-BQ Datasheet - Page 32
![IC SLIC/CODEC DUAL-CH 64TQFP](/photos/16/12/161288/tqfp-64_sml.jpg)
SI3220-BQ
Manufacturer Part Number
SI3220-BQ
Description
IC SLIC/CODEC DUAL-CH 64TQFP
Manufacturer
Silicon Laboratories Inc
Series
ProSLIC®r
Specifications of SI3220-BQ
Package / Case
*
Function
Subscriber Line Interface Concept (SLIC), CODEC
Interface
GCI, PCM, SPI
Number Of Circuits
2
Voltage - Supply
3.3V, 5V
Current - Supply
65mA
Power (watts)
941mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Includes
Battery Switching, BORSCHT Functions, DTMF Generation and Decoding, FSK Tone Generation, Modem and Fax Tone Detection
Product
Telecom
Supply Voltage (min)
3.13 V
Supply Current
22 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Number Of Channels
2
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI3220-BQ
Manufacturer:
TONTEK
Quantity:
12 000
Company:
Part Number:
SI3220-BQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Si3220/25 Si3200/02
battery supply that is provided. Because the battery
supply depends on the state of the input supply (i.e.,
charging, discharging, or battery backup mode), the
user must decide how much loop current is required and
determine the maximum loop impedance that can be
driven based on the battery supply provided. The
minimum battery supply required can be calculated with
the following equation:
where V
The default V
overhead for a 3.1 dBm signal into a 600 Ω loop
impedance with an I
setting of 4 mA. A V
headroom to source a maximum I
3.1 dBm audio signal and an ABIAS setting of 16 mA.
For a typical operating condition of V
I
These conditions apply when the dc-sensing inputs
32
LIM
= 22 mA:
CM
Figure 15. Simplified Dual ProSLIC Linefeed Architecture for TIP and RING Leads
V
and V
OC MAX
,
CM
V
OV
BAT
(Diagram Illustrates either TIP or RING Lead of a Single Channel)
=
value of 3 V provides sufficient
LIM
are provided in Table 8 on page 15.
OV
≥
56 V
V
setting of 22 mA and an ABIAS
value of 4 V provides sufficient
OC
TIP or
RING
–
+
(
3 V
C
V
AC
CM
Control
Audio
+
+
4 V
LOOP
Codec
Audio
V
V
V
V
BATH
BATL
BAT
OV
)
A/D
D/A
=
BAT
Control
R
of 45 mA with a
Audio
Loop
DC
49 V
Audio
Diagnostic
Filters
= –56 V and
DSP
Rev. 1.3
Current
Mirror
Σ
(STIPDCa/b and SRINGDCa/b) are placed on the SLIC
side of any protection resistance placed in series with
the TIP and RING leads. If line-side sensing is desired,
both V
equal to R
protection resistor. Other safety precautions may also
apply.
See "3.14.3. Linefeed Overhead Voltage Considerations
During Ringing" on page 54 for details on calculating the
overhead voltage during the ringing state.
The Dual ProSLIC chipset uses both voltage and
current information to control TIP and RING. Sense
resistor R
RING; Capacitor C
the TIP and RING leads to be measured. The Si3220
and Si3225 both use the Si3200/2 to drive TIP and
RING and isolate the high-voltage line from the low-
voltage CMOS devices.
The Si3220 and Si3225 measure voltage at various
nodes to monitor the linefeed current. R
provide these measuring points. The sense circuitry is
calibrated on-chip to guarantee measurement accuracy.
See "3.6. Linefeed Calibration" on page 37 for details.
Low
Frequency
Diagnostic
Filters
Si3200/2
Control
SLIC DAC
Loop
SLIC
Control
Battery
Select
OV
Monitor A/D
A/D
D/A
PROT
DC
and V
Control
measures dc line voltages on TIP and
SLIC
x I
CM
LIM
AC
V
R
BAT
must be increased by a voltage
BAT
where R
Si3220/
couples the ac line voltages on
Si3225
Sense
PROT
is the value of each
DC
and R
BAT