HMC1002-TR Honeywell Microelectronics & Precision Sensors, HMC1002-TR Datasheet
HMC1002-TR
Specifications of HMC1002-TR
342-1070-1
342-1070
Available stocks
Related parts for HMC1002-TR
HMC1002-TR Summary of contents
Page 1
Magnetic Sensors HMC1001/1002/1021/1022 The Honeywell HMC100x and magnetic sensors are one and two-axis surface mount sensors designed for low field magnetic sensing. By adding supporting signal processing, cost effective magnetometers or compassing solutions are enabled. Th ese ...
Page 2
HMC1001/1002/1021/1022 HMC1001/1002 SPECIFICATIONS Characteristics Bridge Elements Supply Resistance Operating Temperature Storage Temperature Field Range Full scale (FS) – total applied field Linearity Error Hysteresis Error Repeatability Error S/R Repeatability Output variation after alternate S/R pulses Bridge Offset Field = 0 ...
Page 3
HMC1001/1002/1021/1022 HMC1021/1022 SPECIFICATIONS Characteristics Bridge Elements Supply Resistance Operating Temperature Storage Temperature Field Range Full scale (FS) – total applied field Linearity Error Hysteresis Error Repeatability Error Bridge Offset Field = 0 gauss after Set pulse Sensitivity ...
Page 4
HMC1001/1002/1021/1022 KEY PERFORMANCE DATA 4 www.honeywell.com ...
Page 5
HMC1001/1002/1021/1022 PACKAGE / PINOUT SPECIFICATIONS Arrow indicates direction of applied field that generates a positive output voltage after a SET pulse. BASIC DEVICE OPERATION The Honeywell HMC100x and HMC102x Anisotropic Magneto-Resistive (AMR) sensors are simple resistive Wheatstone bridges to measure ...
Page 6
HMC1001/1002/1021/1022 These resistive elements are aligned together to have a common sensitive axis (indicated by arrows on the pinouts) that will provide positive voltage change with magnetic fields increasing in the sensitive direction. Because the output only is in proportion ...
Page 7
HMC1001/1002/1021/1022 For simpler circuits with less critical requirements for noise and accuracy, a single polarity pulse circuit may be employed periodically (all sets or all resets). With these uni-polar pulses, several uni-polar pulses become close in performance to a single ...
Page 8
HMC1001/1002/1021/1022 SET/RESET STRAP OPERATION The reasons to perform a set or reset on an AMR sensor are recover from a strong external magnetic field that likely has re-magnetized the sensor optimize the magnetic domains for most ...
Page 9
... Three of these strap resistances are chosen since many users desire 3-axis magnetic field sensing that comes from a pairing of a HMC1001 and a HMC1002. Also this combination of three series straps is also used on the HMC2003 hybrid sensor module and in the HMR2300 Smart Digital Magnetometer. ...
Page 10
... D1 1N4148 Figure 4 – Higher Voltage Set/Reset Circuit for HMC1001 & HMC1002 The three strap resistances are chosen at 1.8 ohms, or the worst-case high resistance points. Since they require a minimum of 3 amperes peak, the series combination requires at least 16.2 volts circuit Vdd of about 18 volts would about the right level to drive the strap load and allocate for losses in the C1 capacitor ESR and the MOSFET switches X1 and X2. C1’ ...
Page 11
... The resistors around the op-amp are chosen for earth’s magnetic field strength (about 0.6 gauss) levels and to match with the sensor impedance. The 4.99k-ohm resistors are a bridging impedance that is normally chosen times larger than the sensor bridge resistance elements (HMC1002) at 850 ohms. The www.honeywell.com ...
Page 12
... As a compass, the two outputs constrain the earth’s magnetic field measurement to horizontal orientations with the Xout and Yout feeding the heading equation of arctan (Yout/Xout) in degrees. The Xout direction of the HMC1002 should be mounted to the forward direction of the product for proper orientation tilt-compensated compass is desired, a third axis could be made from the spare LMV324N amplifier and a HMC1001 sensor ...
Page 13
HMC1001/1002/1021/1022 R1 R1 1.1K 1. 1.1K 1.1K HMC1021 HMC1021 R12 R12 4.5 4.5 MOUNTING CONSIDERATIONS Stencil Design and Solder Paste A 4 mil stencil and 100% paste coverage is recommended for the electrical contact pads. Pick ...
Page 14
HMC1001/1002/1021/1022 PACKAGE OUTLINES 14 www.honeywell.com ...
Page 15
... ORDERING INFORMATION Ordering Number Product HMC1001 One Axis Magnetic Sensor, 8-pin SIP HMC1002 Two Axis Magnetic Sensor, 20-pin SOIC HMC1002-TR HMC1021S One Axis Magnetic Sensor, 8-pin SOIC HMC1021S-TR HMC1021Z One Axis Magnetic Sensor, 8-pin SIP HMC1022 Two Axis Magnetic Sensor, 16-pin SOIC HMC1022-TR * When ordering the – ...