DG408DJ+ Maxim Integrated Products, DG408DJ+ Datasheet - Page 6

• Manufacturer Part Number: DG408DJ+
• Description: IC MULTIPLEXER 8X1 16DIP
• Manufacturer: Maxim Integrated Products
• Type: Analog Multiplexerr

Specifications of DG408DJ+

• Function: Multiplexer
• Circuit: 1 x 8:1
• On-state Resistance: 100 Ohm
• Voltage Supply Source: Single, Dual Supply
• Voltage - Supply, Single/dual (±): 5 V ~ 30 V, ± 5 V ~ 20 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 16-DIP (0.300", 7.62mm)
• Product: Multiplexer
• Number Of Lines (input / Output): 8.0 / 1.0
• Supply Voltage (max): 30 V
• Supply Voltage (min): 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: Through Hole
• Number Of Input Lines: 8.0
• Number Of Output Lines: 1.0
• Power Dissipation: 842 mW
• Package: 16PDIP N
• Maximum On Resistance: 175@12V Ohm
• Maximum Propagation Delay Bus To Bus: 175@±15V|450@12V ns
• Maximum High Level Output Current: 30 mA
• Multiplexer Architecture: 8:1
• Maximum Turn-off Time: 300@12V ns
• Maximum Turn-on Time: 600@12V ns
• Power Supply Type: Single|Dual
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Improved, 8-Channel/Dual 4-Channel,
CMOS Analog Multiplexers
Using supply voltages less than ±15V reduces the ana-
log signal range. The DG408/DG409 switches operate
with ±5V to ±20V bipolar supplies or with a +5V to
+40V single supply. Connect V- to GND when operat-
ing with a single supply. Both device types can also
operate with unbalanced supplies, such as +24V and
-5V. The Typical Operating Characteristics graphs
show typical on-resistance with 20V, 15V, 10V, and 5V
supplies. (Switching times increase by a factor of two or
more for operation at 5V.)
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings may cause permanent damage to the devices.
Always sequence V+ on first, then V-, followed by the
logic inputs, S or D. If power-supply sequencing is not
possible, add two small signal diodes in series with
supply pins for overvoltage protection (Figure 1).
Adding diodes reduces the analog signal range to 1V
below V+ and 1V above V-, but does not affect the
devices’ low switch resistance and low leakage charac-
teristics. Device operation is unchanged, and the differ-
ence between V+ and V- should not exceed +44V.
6
______________________________________________________________Pin Description
_______________________________________________________________________________________
1, 15, 16
DG408
9–12
4–7
13
14
—
—
—
—
2
3
8
PIN
Supply Voltages Other than 15V
Applications Information
DG409
10–13
1, 16
8, 9
4–7
14
15
—
—
—
—
2
3
Overvoltage Protection
Operation with
A0, A2, A1
S1A–S4A
S4B–S1B
DA, DB
NAME
A0, A1
S1–S4
S8–S5
GND
EN
V+
V-
D
Address Inputs
Address Inputs
Enable Input
Negative Supply Voltage Input
Bidirectional Analog Inputs
Bidirectional Analog Inputs
Bidirectional Analog Output
Bidirectional Analog Outputs
Bidirectional Analog Inputs
Bidirectional Analog Inputs
Positive Supply Voltage Input
Ground
Figure 1. Overvoltage Protection Using External Blocking
Diodes
V
g
S
FUNCTION
V+
V-
DG408
DG409
D