SP3508EB Exar Corporation, SP3508EB Datasheet - Page 27

• Manufacturer Part Number: SP3508EB
• Description: LIN Transceivers 20Mbps Multiprotocol Transceiver 8Ch 3.3V
• Manufacturer: Exar Corporation
• Series: -r

Specifications of SP3508EB

• Main Purpose: Interface, Transceiver RS-232, RS-449, EIA-530(A), X.21
• Embedded: No
• Utilized Ic / Part: SP3508
• Primary Attributes: Internal Line or Digital Loopback Testing
• Secondary Attributes: 8 Drivers and 8 Receivers
• Lead Free Status / Rohs Status: Details

The same receivers also incorporate a ter-
mination network internally for V.35 applica-
tions. For V.35, the receiver input termination
is a “Y” termination consisting of two 51Ω
resistors connected in series and a 124Ω
resistor connected between the two 50Ω
resistors and GND. The receiver itself is
identical to the V. receiver.
The differential receivers can be configured
to be ITU-T-V.0 single-ended receivers by
internally connecting the non-inverting input
to ground. This is internally done by default
from the decoder. The non-inverting input is
rerouted to V0GND and can be grounded
separately. The ITU-T-V.0 receivers can
operate over 20Kbps and are used in RS-
449/V.36, EA-530, EA-530A and X.2
modes as Category II signals as indicated
by their corresponding specifications. All
receivers include an enable/disable line
for disabling the receiver output allowing
convenient half-duplex configurations. The
enable pins will either enable or disable the
output of the receivers according to the ap-
propriate active logic illustrated on Figure
44. The receiver’s enable lines include an
internal pull-up or pull-down device, depend-
ing on the active polarity of the receiver, that
enables the receiver upon power up if the
enable lines are left floating. During disabled
conditions, the receiver outputs will be at
a high impedance state. If the receiver is
disabled any associated termination is also
disconnected from the inputs.
All receivers include a fail-safe feature that
outputs a logic high when the receiver inputs
Figure 45. Charge Pump - Phase .
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (50)668-707 • www.exar.com
C
1
–3 V
+
–
V
CC
= +3V
C
2
+3V
–3 V
+
–
27
are open, terminated but open, or shorted
together. For single-ended V.28 and V.0
receivers, there are internal 5kΩ pull-down
resistors on the inputs which produces a
logic high (“”) at the receiver outputs. The
differential receivers have a proprietary cir-
cuit that detect open or shorted inputs and
if so, will produce a logic HIGH (“”) at the
receiver output.
CHARGE PUMP
SP3508 uses an internal capacitive charge
pump to generate Vdd and Vss. The design
is a patented (5,306,954) four-phased volt-
age shifting charge pump converters that
converts the input voltage of 3.3V to nomi-
nal output voltages of +/-6V (Vdd & Vss).
SP3508 also includes an inverter block
that inverts Vcc to -Vcc (Vss2). There is a
free-running oscillator that controls the four
phases of the voltage shifting. A description
of each phase follows.
4-phased doubler pump
Phase 1
-V
the clock cycle, the positive side of capacitors
C and C2 are initially charged to V
is then switched to ground and the charge in
C- is transferred to C2-. Since C2+ is con-
nected to V
capacitor C2 is now 2xV
SS
C
+
C
–
VDD
VSS1
+
–
charge storage -During this phase of
V
V
DD
SS1
S tora ge C apacitor
S tora ge C apacitor
CC
, the voltage potential across
CC
.
SP3508_00_072208
FEATURES
CC
. C+