LE9500ABJCT Zarlink, LE9500ABJCT Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/7/726/zarlink_sml.jpg)
LE9500ABJCT
Manufacturer Part Number
LE9500ABJCT
Description
SLIC 1-CH 52dB 40mA 3.3V 28-Pin PLCC T/R
Manufacturer
Zarlink
Datasheet
1.LE9500ABJC.pdf
(25 pages)
Specifications of LE9500ABJCT
Package
28PLCC
Number Of Channels Per Chip
1
Polarity Reversal
Yes
Longitudinal Balanced
52(Min) dB
Loop Current
40(Typ) mA
Minimum Operating Supply Voltage
3.13 V
Typical Operating Supply Voltage
3.3 V
Typical Supply Current
4.7 mA
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LE9500ABJCT
Manufacturer:
LEGERIEY
Quantity:
20 000
Company:
Part Number:
LE9500ABJCT.JA
Manufacturer:
Zarlink
Quantity:
305
Company:
Part Number:
LE9500ABJCT.JC
Manufacturer:
Zarlink
Quantity:
336
Company:
Part Number:
LE9500ABJCT.JD
Manufacturer:
Zarlink
Quantity:
15 628
Pre-trip immunity
Ringing will not be tripped by the following loads across Tip and Ring as shown in the reference schematic in the this document.
Ringing frequency = 17 Hz to 23 Hz otherwise specified.
•
•
OPERATING STATES
Operating State Definitions
Forward Active
•
•
•
•
•
Reverse Active
•
•
•
•
•
Scan
•
•
•
•
On-Hook Transmission—Forward Battery
•
•
•
•
10-kΩ resistor in parallel with 5 Ringer Equivalency Number (REN) (equivalent of 1386-Ω + 40-µF) per GR-909 Issue 2,
December 2004
10-kΩ resistor in parallel with a 2-µF capacitor in parallel with 5 Ringer Equivalency Number (REN) (equivalent of 1386-Ω +
40-µF) per GR 57 Issue 1 October 2001.
Pin PT is positive with respect to PR.
V
Loop closure and common-mode detect are active.
Ring trip detector is turned off to conserve power.
Overhead is set to nominal 7.2 V for undistorted transmission of 3.14 dBm into 900 Ω with 500 mVrms of PPM.
Pin PR is positive with respect to PT.
V
Loop closure and common-mode detect are active.
Ring trip detector is turned off to conserve power.
Overhead is set to nominal 7.2 V for undistorted transmission of 3.14 dBm into 900 Ω with 500 mVrms of PPM.
Except for loop closure, all circuits (including ring trip and common-mode detector) are powered down.
On-hook transmission is disabled.
Pin PT is positive with respect to PR and V
The tip to ring on-hook differential voltage will be typically between –44 V and –51 V with a –51 V to –100 V primary battery.
Pin PT is positive with respect to PR.
V
Supervision circuits, loop closure, and common-mode detect are active.
Ring trip detector is turned off to conserve power.
BAT2
BAT2
BAT1
Table 7. Control States
Table 8. Supervision Coding
0 = off-hook or ring trip or thermal shutdown or ring ground.
1 = on-hook and no ring trip and no thermal shutdown and no ring ground.
is applied to tip/ring drive amplifiers.
is applied to tip/ring drive amplifiers.
is applied to tip/ring drive amplifiers.
B0
0
0
0
0
1
1
1
1
B1
0
1
0
1
1
0
1
0
B2
1
1
0
0
0
0
1
1
BAT1
Forward active
Reverse active
On-hook transmission forward battery
On-hook transmission reverse battery
Ground start
Scan
Disconnect (default device power up state)
Ring
Zarlink Semiconductor Inc.
is applied to tip/ring.
NSTAT
12
Operating State