MAX884ESA Maxim Integrated Products, MAX884ESA Datasheet - Page 9

• Manufacturer Part Number: MAX884ESA
• Description: Low Dropout (LDO) Regulators 5/3.3/AdjV 200mA Linear Regulator
• Manufacturer: Maxim Integrated Products

Specifications of MAX884ESA

• Number Of Outputs: 1
• Polarity: Positive
• Input Voltage Max: 11.5 V
• Output Voltage: 1.25 V to 11 V or 3.3 V
• Output Type: Adjustable, Fixed
• Dropout Voltage (max): 0.32 V at 100 mA
• Output Current: 200 mA
• Line Regulation: 40 mV
• Load Regulation: 100 mV
• Voltage Regulation Accuracy: 5 %
• Maximum Power Dissipation: 1.5 W
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SOIC-8 Narrow
• Minimum Operating Temperature: - 40 C
• Reference Voltage: 1.24 V

The MAX882/MAX883/MAX884 also include a foldback
current limiter. It monitors and controls the pass transis-
tor’s gate voltage, estimating the output current and
limiting it to 430mA for output voltages above 0.8V and
(V
0.8V, implying a short-circuit condition, the output cur-
rent is limited to 170mA. The output can be shorted to
ground for 1min without damaging the device if the
package can dissipate (V
ing T
and (V
limiting is allowed, to provide maximum load drive.
Thermal overload protection limits total power dissipa-
tion in the MAX882/MAX883/MAX884. When the junc-
tion temperature exceeds T
sensor sends a signal to the shutdown logic, turning off
the pass transistor and allowing the IC to cool. The
thermal sensor turns the pass transistor on again after
the IC’s junction temperature cools by 10°C, resulting in
a pulsed output during thermal overload conditions.
Thermal overload protection is designed to protect the
MAX882/MAX883/MAX884 if fault conditions occur. It is
not intended to be used as an operating mode.
Prolonged operation in thermal-shutdown mode may
reduce the IC’s reliability. For continual operation, do
not exceed the absolute maximum junction temperature
rating of T
Figure 2. Adjustable Output Using External Feedback
Resistors
IN
INPUT
VOLTAGE
V
O.1µF
OUT
( ) ARE FOR MAX882.
- V
J
C
IN
IN
= +150°C. When the output is greater than 0.8V
= V
OUT
SET
- V
J
R1 + R2
= +150°C.
) > 0.7V. If the output voltage drops below
OUT
R2
OFF
(STBY)
IN
LBI
, V
) < 0.7V (dropout operation), no current
SET
Thermal Overload Protection
_______________________________________________________________________________________
MAX882
MAX883
MAX884
= 1.20V
Foldback Current Limiting
GND
IN
5V/3.3V or Adjustable, Low-Dropout,
x 170mA) without exceed-
J
OUT
SET
= +160°C, the thermal
Low I
R1
R2
C
2.2µF
OUT
VOLTAGE
OUTPUT
Q
LOAD
, 200mA Linear Regulators
Maximum power dissipation of the MAX882/MAX883/
MAX884 depends on the thermal resistance of the case
and PC board, the temperature difference between the
die junction and ambient air, and the rate of
air flow. The power dissipation across the device is
P = I
is as follows:
where (T
the MAX882/MAX883/MAX884 die junction and the sur-
rounding air, θ
the package chosen, and θ
through the PC board, copper traces, and other materi-
als to the surrounding air.
The 8-pin small-outline package for the MAX882/
MAX883/MAX884 features a special lead frame with a
lower thermal resistance and higher allowable power
dissipation. This package’s thermal resistance package
is θ
8-pin plastic DIP package and θ
pin ceramic DIP package.
Figure 3. Setting an Undervoltage Lockout Threshold Using
STBY
INPUT
VOLTAGE
Power Dissipation and Operating Region
JB
V
O.1µF
OUT
STBY TRIP
C
= 53°C/W, compared with θ
IN
J
(V
- T
= V
IN
R1
R2
STBY
A
- V
) is the temperature difference between
JB
R1+ R2
OUT
R2
(or θ
P
IN
LBI
STBY
=
, V
). The resulting power dissipation
STBY
(
JC
θ
(T
JB
MAX882
) is the thermal resistance of
= 1.20V
J
GND
BA
−
+
θ
T )
A
is the thermal resistance
BA
JB
SET
)
JB
OUT
= 125°C/W for an 8-
= 110°C/W for an
C
2.2µF
OUT
VOLTAGE
OUTPUT
9