MAX4605CSE Maxim Integrated Products, MAX4605CSE Datasheet - Page 8

• Manufacturer Part Number: MAX4605CSE
• Description: Analog Switch ICs
• Manufacturer: Maxim Integrated Products

Specifications of MAX4605CSE

• Switch Configuration: SPST
• On Resistance (max): 8 Ohms at 12 V
• On Time (max): 220 ns at 12 V
• Off Time (max): 160 ns at 12 V
• Supply Voltage (max): 36 V
• Supply Voltage (min): 4.5 V
• Maximum Power Dissipation: 696 mW
• Maximum Operating Temperature: + 70 C
• Package / Case: SOIC-16 Narrow
• Minimum Operating Temperature: 0 C
• Switch Current (typ): +/- 0.000001 mA at +/- 15 V
• Lead Free Status / Rohs Status: No

5 , Quad, SPST, CMOS Analog Switches
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
Always sequence V+ on first, then V-, followed by the
logic inputs, NO, or COM. If power-supply sequencing
is not possible, add two small signal diodes (D1, D2) in
series with supply pins for overvoltage protection
(Figure 1). Adding diodes reduces the analog signal
range to one diode drop below V+ and one diode drop
above V-, but does not affect the devices’ low switch
resistance and low leakage characteristics. Device
operation is unchanged, and the difference between
V+ and V- should not exceed 44V. These protection
diodes are not recommended when using a single supply.
In 50Ω systems, the high-frequency on-response of
these parts extends from DC to above 100MHz with a
typical loss of -2dB. When the switch is turned off, how-
ever, it behaves like a capacitor, and off isolation
decreases with increasing frequency. (Above 300MHz,
the switch actually passes more signal turned off than
turned on.) This effect is more pronounced with higher
source and load impedances.
Above 5MHz, circuit board layout becomes critical, and
it becomes difficult to characterize the response of the
Figure 2. Switching-Time Test Circuit
8
_______________________________________________________________________________________
OUTPUT
SWITCH
LOGIC
INPUT
+3V
Off-Isolation at High Frequencies
0
0
Applications Information
LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES
THAT HAVE THE OPPOSITE LOGIC SENSE.
t
V
ON
50%
O
Overvoltage Protection
0.9V
0
t
OFF
t r < 20ns
t f < 20ns
0.9V
0
SWITCH
LOGIC
INPUT
INPUT
switch independent of the circuit. The graphs shown in
the Typical Operating Characteristics were taken using
a 50Ω source and load connected with BNC connec-
tors to a circuit board deemed “average;” that is,
designed with isolation in mind, but not using strip-line
or other special RF circuit techniques. For critical appli-
cations above 5MHz, use the MAX440, MAX441, and
MAX442, which are fully characterized up to 160MHz.
Figure 1. Overvoltage Protection Using External Blocking
Diodes
V
COM_
COM_
REPEAT TEST FOR EACH SWITCH. FOR LOAD
CONDITIONS, SEE Electrical Characteristics.
C
V
O
L
INCLUDES FIXTURE AND STRAY CAPACITANCE.
= V
COM_
IN_
+5V
GND
COM
V
0
L
(
R
L
R
+ R
L
ON
)
*
*
OR NC_
+15V
-15V
V-
V+
V+
V-
-15V
+15V
NO_
D1
D2
* INTERNAL PROTECTION DIODES
*
*
R
100
L
MAX4604
MAX4605
MAX4606
SWITCH
OUTPUT
MAX4604
MAX4605
MAX4606
C
35pF
NO_
L
V
O