ATA5429-PLUW Atmel, ATA5429-PLUW Datasheet - Page 14
![](/photos/40/57/405769/48pin_qfn_sml.jpg)
ATA5429-PLUW
Manufacturer Part Number
ATA5429-PLUW
Description
Manufacturer
Atmel
Datasheet
1.ATA5429-PLUW.pdf
(100 pages)
Specifications of ATA5429-PLUW
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Product Depth (mm)
7mm
Product Height (mm)
0.9mm
Product Length (mm)
7mm
Lead Free Status / Rohs Status
Compliant
3.4
3.5
3.6
14
Frequency Accuracy of the Crystals
RX Supply Current versus Temperature and Supply Voltage
Blocking, Selectivity
ATA5423/ATA5425/ATA5428/ATA5429
The XTO is an amplitude regulated Pierce oscillator with integrated load capacitors. The initial
tolerances (due to the frequency tolerance of the XTAL, the integrated capacitors on XTAL1,
XTAL2 and the XTO’s initial transconductance gm) can be compensated to a value within
±0.5 ppm by measuring the CLK output frequency and programming the control registers 2 and
3 (see
ence of less than ±2 ppm over temperature and supply voltage due to the band gap controlled
gm of the XTO.
The needed frequency stability of the used crystals over temperature and aging is hence
±58 kHz/315 MHz – 2
±58 kHz/345 MHz – 2
±58 kHz/433.92 MHz – 2
±58 kHz/868.3 MHz – 2
±58 kHz/915 MHz – 2
Thus, the used crystals in receiver and transmitter each need to be better than ±89.6 ppm for
315 MHz, ±81.6 ppm for 345 MHz, ±64.3 ppm for 433.92 MHz, ±30.9 ppm for 868.3 MHz and
±29.2 ppm for 915 MHz. In access control systems it may be advantageous to have a more tight
tolerance at the Base-station in order to relax the requirement for the remote control unit.
Table 3-5
supply voltage and temperature with VS = VS1 = VS2. As can be seen, the supply current at
2.4 V and –40°C is less than the typical supply current; this is useful because this is also the
operation point where a lithium cell has the worst performance. The typical supply current at
315 MHz, 345 MHz, 868.3 MHz or 915 MHz in RX mode is about the same as for 433.92 MHz.
Table 3-5.
As can be seen in
higher than the sensitivity level in the presence of very large blockers of –47 dBm/–34 dBm with
small frequency offsets of ±1 ±10 MHz.
Figure 3-3
measurements were done with a signal of 433.92 MHz/FSK/20 Kbit/s/±16 kHz/ Manchester, and
with a level of –106 dBm + 3 dB = –103 dBm which is 3 dB above the sensitivity level. The fig-
ures show how much larger than –103dBm a continuous wave signal can be before the BER is
higher than 10
page 11
-103 dBm + 56 dB = –47 dBm. These values, together with the good intermodulation perfor-
mance, avoid the need for a SAW filter in the remote control unit application.
VS = VS1 = VS2
T
T
T
Table 7-7 on page 39
amb
amb
amb
At 1 MHz, for example, the blocker can be 56 dB higher than –103 dBm which is
shows the typical supply current at 433.92 MHz of the transceiver in RX mode versus
= –
shows narrow band blocking and
=
=
25°C
85°C
40°C
Measured 433.92 MHz Receive Supply Current in FSK Mode
–3
. The measurements were done at the 50 input according to
Figure 3-3
±2.5 ppm = ±179.2 ppm for 315 MHz,
±2.5 ppm = ±163.2 ppm for 345 MHz,
±2.5 ppm = ±58.4 ppm for 915 MHz.
±2.5 ppm = ±61.8 ppm for 868.3 MHz and
±2.5 ppm = ±128.6 ppm for 433.92 MHz,
and
and
10.9 mA
8.4 mA
9.9 mA
Table 7-10 on page
2.4V
Figure 3-4 on page
Figure 3-4
40). The XTO then has a remaining influ-
15, the receiver can receive signals 3 dB
wide band blocking characteristics. The
10.3 mA
11.3 mA
8.8 mA
3.0V
11.8 mA
10.8 mA
9.2 mA
4841D–WIRE–10/07
Figure 3-1 on
3.6V