ELANSC410-33AC AMD (ADVANCED MICRO DEVICES), ELANSC410-33AC Datasheet - Page 17

• Manufacturer Part Number: ELANSC410-33AC
• Manufacturer: AMD (ADVANCED MICRO DEVICES)

Specifications of ELANSC410-33AC

• Lead Free Status / Rohs Status: Not Compliant

Serial Port
The ÉlanSC400 and ÉlanSC410 microcontrollers in-
clude an industry-standard 16550A UART. The UART
can be used to drive a standard 8-pin serial interface or
a 2-pin infrared interface. The serial interface and infra-
red interface signals are available on the ÉlanSC400
and ÉlanSC410 microcontrollers at all times, though
only one is available at any given time.
The UART powers up as a 16450-compatible device. It
can be switched to and from the FIFO (16550) mode
under software control. In the FIFO mode, the receive
and the transmit circuitry are each enhanced by sepa-
rate 16-byte FIFOs to off-load the CPU from repetitive
service routines.
The serial port includes the following features:
Keyboard Interfaces
The integrated keyboard controller has the following
features:
Programmable General-Purpose
Inputs and Outputs
The chip supports several general-purpose I/O signals
(GPIOs) that can be used on the system board. There
are two classifications of GPIO available: the GPIOx
signals, which are programmable as inputs or outputs
only, and the GPIO_CSx signals.
The GPIO_CSx signals have many programmable op-
tions. They can be configured as chip selects. As out-
puts, these signals are individually programmable to be
High or Low for the following PMU modes: Hyper, High-
Speed, Low-Speed, Standby, and Suspend. As inputs,
they can be programmed to cause System Manage-
ment Interrupts (SMIs), Non-Maskable Interrupts
Eight-pin interface: serial in, serial out, two modem
control lines, and four modem status lines
Separately enabled receiver line status, receiver
data, character timeout, transmitter holding register,
and modem status interrupts
Baud-rate generator provides input clock divisor
from 1 to 65535 to create 16x clock
5-, 6-, 7-, or 8-bit data
Even, odd, stick, or no parity generation and
checking
1, 1-1/2 or 2 stop-bit generation
Break generation/detection
Matrix keyboard support with up to 15 rows and 8
columns
Hardware support for software emulation of the
System Control Processor (SCP) emulation logic
XT keyboard interface
Élan™SC400 and ÉlanSC410 Microcontrollers Data Sheet
(NMIs), wake-ups, or activities for the power manage-
ment unit. They can also be used as I/O or memory
chip selects.
Infrared Port for Wireless Communication
The ÉlanSC400 and ÉlanSC410 microcontrollers sup-
port infrared data transfer. This support consists of
adding additional transmit and receive serializers as
well as a controlling state machine and DMA interface
to the internal UART.
The integrated infrared port includes these features:
Dual PC Card Controller
(ÉlanSC400 Microcontroller Only)
The PC Card host bus adapter included on the
ÉlanSC400 microcontroller conforms to PCMCIA Stan-
dard Release 2.1 . It provides support for two sockets,
each implementing the PC Card memory and I/O inter-
faces. The PC Card controller is not supported on the
ÉlanSC410 microcontroller.
The PC Card controller includes the following features:
Of the two PC Card sockets supported, only one is
available in all modes of operation. The second socket
is multiplexed with the parallel port and GPIO features.
Register set compatibility with the 82365SL PC Card
Interface Controller is maintained where features are
common to both controllers.
Of the ten memory windows available, six are dedi-
cated to the PC Card controller and four are shared
with memory mapping system (MMS) Windows C–F.
Two of the three ROM/Flash memory chip selects can
be remapped to a PC Card socket via pinstrap or soft-
ware control. This feature supports reprogramming of
soldered down Flash memory boot devices and also
simplifies testing of BIOS/XIP OS code.
Graphics Controller for CGA-Compatible
Text and Graphics
(ÉlanSC400 Microcontroller Only)
The graphics controller included on the ÉlanSC400 mi-
crocontroller offers a low-cost integrated graphics solu-
tion for the mobile terminal market. Integration with the
main processor and system logic affords the advan-
Low-speed mode supports all bit rates from UART,
up to 115 Kbit/s
High-speed mode transfers 1.152 Mbit/s using DMA
ExCA-compliant, 82365-register-set compatible
8-bit and 16-bit data bus
DMA transfers between I/O PC cards and system
DRAM
Ten available memory windows, five per socket
17