AM29DL324GB-70EI Spansion Inc., AM29DL324GB-70EI Datasheet - Page 24

• Manufacturer Part Number: AM29DL324GB-70EI
• Manufacturer: Spansion Inc.

Specifications of AM29DL324GB-70EI

• Cell Type: NOR
• Density: 32Mb
• Access Time (max): 70ns
• Interface Type: Parallel
• Boot Type: Bottom
• Address Bus: 22/21Bit
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: -40C to 85C
• Package Type: TSOP
• Program/erase Volt (typ): 3/8.5 to 9.5V
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8/16Bit
• Number Of Words: 4M/2M
• Supply Current: 16mA
• Mounting: Surface Mount
• Pin Count: 48
• Lead Free Status / Rohs Status: Not Compliant

data protection measures prevent accidental erasure
or programming, which might otherwise be caused by
spurious system level signals during V
and power-down transitions, or from system noise.
Low V
When V
cept any write cycles. This protects data during V
power-up and power-down. The command register
and all internal program/erase circuits are disabled,
and the device resets to the read mode. Subsequent
writes are ignored until V
system must provide the proper signals to the control
pins to prevent unintentional writes when V
greater than V
Write Pulse “Glitch” Protection
Noise pulses of less than 5 ns (typical) on OE#, CE#
or WE# do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# =
V
CE# and WE# must be a logical zero while OE# is a
logical one.
Power-Up Write Inhibit
If WE# = CE# = V
the device does not accept commands on the rising
edge of WE#. The internal state machine is automati-
cally reset to the read mode on power-up.
22
IL
(Word Mode)
, CE# = V
Addresses
1Ah
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
CC
CC
Write Inhibit
is less than V
IH
LKO
or WE# = V
.
(Byte Mode)
IL
Addresses
and OE# = V
2Ch
20h
22h
24h
26h
28h
2Ah
2Eh
30h
32h
34h
LKO
CC
IH
, the device does not ac-
is greater than V
. To initiate a write cycle,
IH
Table 10. CFI Query Identification String
during power up,
0051h
0052h
0059h
0002h
0000h
0040h
0000h
0000h
0000h
0000h
0000h
Data
CC
power-up
D A T A
LKO
. The
CC
Query Unique ASCII string “QRY”
Primary OEM Command Set
Address for Primary Extended Table
Alternate OEM Command Set (00h = none exists)
Address for Alternate OEM Extended Table (00h = none exists)
Am29DL32xG
CC
is
S H E E T
COMMON FLASH MEMORY INTERFACE
(CFI)
The Common Flash Interface (CFI) specification out-
lines device and host system software interrogation
handshake, which allows specific vendor-specified
software algorithms to be used for entire families of
devices. Software support can then be device-inde-
pendent, JEDEC ID-independent, and forward- and
backward-compatible for the specified flash device
families. Flash vendors can standardize their existing
interfaces for long-term compatibility.
This device enters the CFI Query mode when the sys-
tem writes the CFI Query command, 98h, to address
55h in word mode (or address AAh in byte mode), any
time the device is ready to read array data. The
system can read CFI information at the addresses
given in Tables 10–13. To terminate reading CFI data,
the system must write the reset command. The CFI
Query mode is not accessible when the device is exe-
cuting an Embedded Program or Embedded Erase al-
gorithm.
The system can also write the CFI query command
when the device is in the autoselect mode. The device
enters the CFI query mode, and the system can read
CFI data at the addresses given in Tables 10–13. The
system must write the reset command to return the
device to reading array data.
For further information, please refer to the CFI Specifi-
cation and CFI Publication 100, available via the World
Wide Web at
tively, contact an AMD representative for copies of
these documents.
http://www.amd.com/flash/cfi.
Description
25686B10 December 4, 2006
Alterna-