5962-8764802XA E2V, 5962-8764802XA Datasheet - Page 4

• Manufacturer Part Number: 5962-8764802XA
• Manufacturer: E2V

Specifications of 5962-8764802XA

• Lead Free Status / Rohs Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless
a specific exemption has been obtained.
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
drawing shall be as specified on figure 3. When required in groups A, B, or C inspection (see 4.3), the devices shall be
programmed by the manufacturer prior to test in a checkerboard pattern or equivalent ( minimum of 50 percent of the total
number of bits programmed) or to any altered item drawing pattern which includes at least 25 percent of the total number of bits
programmed.
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
case operating temperature range.
tests for each subgroup are defined in table I.
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and
herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
herein) involving devices acquired to this drawing is required for any change that affects this drawing.
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3.
3.2.3.1 Unprogrammed or erased devices. The truth table for unprogrammed devices for contracts involving no altered item
3.2.3.2 Programmed devices. The truth table for programmed devices shall as specified by an attached altered item drawing.
3.2.4 Block diagram(s). The block diagram(s) shall be as specified on figure 4.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
DEFENSE SUPPLY CENTER COLUMBUS
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43218-3990
STANDARD
SIZE
A
REVISION LEVEL
E
SHEET
5962-87648
4