ST10F269-T3 STMicroelectronics, ST10F269-T3 Datasheet - Page 138
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
ST10F269-T3
Manufacturer Part Number
ST10F269-T3
Description
Manufacturer
STMicroelectronics
Datasheet
1.ST10F269-T3.pdf
(162 pages)
Specifications of ST10F269-T3
Cpu Family
ST10
Device Core Size
16b
Frequency (max)
32MHz
Interface Type
ASC/I2C/SSC
Program Memory Type
Flash
Program Memory Size
256KB
Total Internal Ram Size
12KB
# I/os (max)
111
Number Of Timers - General Purpose
4
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (max)
5.5V
Operating Supply Voltage (min)
4.5V
On-chip Adc
16-chx10-bit
Instruction Set Architecture
CISC/RISC
Operating Temp Range
-40C to 125C
Operating Temperature Classification
Automotive
Mounting
Surface Mount
Pin Count
144
Package Type
TQFP
Lead Free Status / Rohs Status
Supplier Unconfirmed
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
ST10F269-T3
21.4.4 - Prescaler Operation
When pins P0.15-13 (P0H.7-5) equal ’001’ during
reset, the CPU clock is derived from the internal
oscillator (input clock signal) by a 2:1 prescaler.
The frequency of f
f
duration of an individual TCL) is defined by the
period of the input clock f
The timings listed in the AC Characteristics that
refer to TCL therefore can be calculated using the
period of f
Note that if the bit OWDDIS in SYSCON register
is cleared, the PLL runs on its free-running
frequency and delivers the clock signal for the
Oscillator Watchdog. If bit OWDDIS is set, then
the PLL is switched off.
21.4.5 - Direct Drive
When pins P0.15-13 (P0H.7-5) equal ’011’ during
reset the on-chip phase locked loop is disabled
and the CPU clock is directly driven from the
internal oscillator with the input clock signal.
The frequency of f
frequency of f
(i.e. the duration of an individual TCL) is defined
by the duty cycle of the input clock f
Therefore, the timings given in this chapter refer to
the minimum TCL. This minimum value can be
calculated by the following formula:
For two consecutive TCLs, the deviation caused
by the duty cycle of f
duration of 2TCL is always 1/f
The minimum value TCL
once for timings that require an odd number of
TCLs (1,3,...). Timings that require an even
number of TCLs (2,4,...) may use the formula:
Note:
138/162
XTAL
and the high and low time of f
The address float timings in Multiplexed
bus mode (t
duration of TCL (TCL
DC
If the bit OWDDIS in SYSCON register is
cleared, the PLL runs on its free-running
frequency and delivers the clock signal for
the Oscillator Watchdog. If bit OWDDIS is
set, then the PLL is switched off.
TCL min
XTAL
max
XTAL
DC
) instead of TCL
for any TCL.
2TCL
=
=
so the high and low time of f
CPU
1
duty cycle
11
XTAL
=
⁄
CPU
and t
f
1
XT
is half the frequency of
XTAL
min
⁄
is compensated, so the
ALl
f XTAL
45
directly follows the
has to be used only
.
XTAL
) use the maximum
min
xl
max
DC
.
.
XTAL
min
CPU
= 1/f
.
(i.e. the
XTAL
CPU
x
21.4.6 - Oscillator Watchdog (OWD)
An on-chip watchdog oscillator is implemented in
the ST10F269-T3. This feature is used for safety
operation with external crystal oscillator (using
direct drive mode with or without prescaler). This
watchdog oscillator operates as following:
The reset default configuration enables the
watchdog oscillator. It can be disabled by setting
the OWDDIS (bit 4) of SYSCON register.
When the OWD is enabled, the PLL runs at its
free-running frequency, and it increments the
watchdog
frequency is between 2 and 10MHz. On each
transition of external clock, the watchdog counter
is cleared. If an external clock failure occurs, then
the watchdog counter overflows (after 16 PLL
clock cycles).
The CPU clock signal will be switched to the PLL
free-running clock signal, and the oscillator
watchdog Interrupt Request (XP3INT) is flagged.
The CPU clock will not switch back to the external
clock even if a valid external clock exits on XTAL1
pin. Only a hardware reset can switch the CPU
clock source back to direct clock input.
When the OWD is disabled, the CPU clock is
always external oscillator clock and the PLL is
switched off to decrease consumption supply
current.
21.4.7 - Phase Locked Loop
For all other combinations of pins P0.15-13
(P0H.7-5) during reset the on-chip phase locked
loop is enabled and it provides the CPU clock (see
Table 34). The PLL multiplies the input frequency
by the factor F which is selected via the
combination of pins P0.15-13 (f
With every F’th transition of f
synchronizes the CPU clock to the input clock.
This synchronization is done smoothly, so the
CPU clock frequency does not change abruptly.
Due to this adaptation to the input clock the
frequency of f
locked to f
of f
individual TCLs.
The timings listed in the AC Characteristics that
refer to TCLs therefore must be calculated using
the minimum TCL that is possible under the
respective circumstances.
CPU
which also effects the duration of
XTAL
counter.
CPU
. The slight variation causes a jitter
is constantly adjusted so it is
The
XTAL
PLL
CPU
the PLL circuit
= f
free-running
XTAL
x F).