DS96173CN National Semiconductor, DS96173CN Datasheet - Page 2

• Manufacturer Part Number: DS96173CN
• Manufacturer: National Semiconductor

Specifications of DS96173CN

• Data Rate: 10Mbps
• Interface Circuit Standard 1: RS-485
• Number Of Receivers: 4
• Number Of Transmitters: Not Required
• Number Of Transceivers: Not Required
• Data Transmission Topology: Multidrop/Multipoint
• Receiver Signal Type: Differential
• Transmitter Signal Type: Not Required
• Single Supply Voltage (typ): 5V
• Single Supply Voltage (min): 4.75V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Supply Current: 75mA
• Power Supply Requirement: Single
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 16
• Package Type: PDIP
• Lead Free Status / Rohs Status: Not Compliant

www.national.com
V
V
V
V
V
V
V
V
I
I
I
I
R
I
I
OZ
I
IH
IL
OS
CC
TH
TL
T+
IH
IL
IC
OH
OL
Absolute Maximum Ratings
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Electrical Characteristics
over recommended temperature, common mode input voltage, and supply voltage ranges, unless otherwise specified
I
Note 2: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices
should be operated at these limits. The tables of “Electrical Characteristics” provide conditions for actual device operation.
Note 3: Unless otherwise specified Min/Max limits apply across the 0˚C to +70˚C range for the DS96173/DS96175. All typicals are given for V
T
Note 4: All currents into the device pins are positive; all currents out of the device pins are negative. All voltages are reference to ground unless otherwise specified.
Note 5: The algebraic convention, when the less positive (more negative) limit is designated minimum, is used in this data sheet for common mode input voltage
and threshold voltage levels only.
Note 6: Hysteresis is the difference between the positive-going input threshold voltage, V
Note 7: Refer to EIA Standards RS-485 for exact conditions.
Note 8: Only one output at a time should be shorted.
Symbol
A
= 25˚C.
− V
Storage Temperature Range
Lead Temperature
sec.)
Maximum Power Dissipation (Note 1) at 25˚C
Supply Voltage
Input Voltage, A or B Inputs
Differential Input Voltage
Enable Input Voltage
T−
Molded DIP
Molded DIP (soldering, 10
N-Molded Package
Differential Input
High Threshold Voltage
Differential Input (Note 5)
Low Threshold Voltage
Hysteresis (Note 6)
Enable Input Voltage HIGH
Enable Input Voltage LOW
Enable Input Clamp Voltage
Output Voltage HIGH
Output Voltage LOW
High Impedance State Output
Line Input Current (Note 7)
Enable Input Current HIGH
Enable Input Current LOW
Input Resistance
Short Circuit Output Current
Supply Current
Parameter
(Notes 3, 4)
−65˚C to
+150˚C
(Note 2)
1.84W
265˚C
±
±
V
V
V
I
V
V
V
Other Input = 0V
V
V
(Note 8)
Outputs Disabled
25V
25V
I
O
O
CM
ID
ID
O
IH
IL
7V
7V
= −18 mA
= 2.7V, I
= 0.5V, I
= 0.4V to 2.4V
= 0.4V
= 200 mV, I
= −200 mV
= 2.7V
= 0V
O
O
2
Conditions
= − 0.4 mA
= 16 mA
OH
Recommended Operating
Conditions
Note 1: Derate molded DIP package 15 mW/˚C above 25˚C.
Supply Voltage (V
Common Mode Input
Differential Input
Output Current High (I
Output Current LOW (I
Operating Temperature (T
= −400 µA
Voltage (V
Voltage (V
T+
Low Level Output Current
, and the negative going input threshold voltage, V
I
I
V
V
OL
OL
I
I
= 12V
= −7V
= 8 mA
= 16 mA
CM
ID
)
)
CC
)
OH
OL
−0.2
Min
−15
2.0
2.7
)
)
A
)
4.75
Min
−7
−7
0
Typ
50
12
Typ Max
25
5
−100
Max
−1.5
0.45
0.50
−0.8
±
−85
−400
0.2
0.8
1.0
5.25
20
75
T−
+12
+12
20
16
70
.
50 mA
CC
= 5V and
Units
mA
µA
˚C
V
V
V
Units
mV
mA
mA
mA
µA
µA
µA
kΩ
V
V
V
V
V
V
V