SI2415-D-FS Silicon Laboratories Inc, SI2415-D-FS Datasheet - Page 225
SI2415-D-FS
Manufacturer Part Number
SI2415-D-FS
Description
IC ISOMODEM SYSTEM-SIDE 16SOIC
Manufacturer
Silicon Laboratories Inc
Specifications of SI2415-D-FS
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 225 of 304
- Download datasheet (5Mb)
4. Issuing ATO to modem will start the V.32bis handshake. The host then waits for the CONNECT message before
5. The host disconnects the V.32bis session (using either +++ followed by ATH, or with DTR, if it has previously
6. The host issues AT+VNH=2 to the modem again to maintain off-hook status for next cleardown.
7. AT\N0 removes error-correction, if it was used during the V.32bis period.
8. SIA protocol communication resumes by starting up the transmitter in Bell 103, SIA mode with AT+F0.
8.1.1.3. Considerations when Disconnecting the Session
Because AT+VNH=2 keeps the modem off-hook during a cleardown, the first ATH or DTR desertion will not put
modem back on-hook but only force AT+VNH=0 (per V.253). The host must issue a second ATH to put the modem
back in on-hook idle state. Alternatively the host could issue a AT+VNH=0, then ATH (or AT+VNH=0;H)
Table 142 lists the AT Commands provided to support SIA Level-3 Protocol communication.
AT+F0
AT Command
sending data. (For an originating modem, the ATO command must be sent as soon as possible so the modem
will be ready when the remote answering modem starts. For an answering modem, the ATO should be delayed
a little to give the remote originating modem a chance to get ready first.)
been enabled with AT&D2).
Table 142. AT Commands Provided to Support SIA Level-3 Protocol Communication
Enable B103 Transmitter for Data Block
transmission.
Modem Function
Rev. 1.3
Modem turns on FSK transmitter and starts marking
for the minimum duration required by standard.
Sends CONNECT message to DTE when that is
accomplished.
Modem will then interpret the first character from
DTE as Block Header and use the byte count to
allow transmission of the specified number of char-
acters to the remote modem and then send OK
message to DTE to indicate ready for next AT com-
mand.
Note1: FSK transmitter remains on. DTE is
expected to issue either a +F2 (detect ACK/NACK)
or another +F0 (to send another data block) com-
mand to the modem.
Note2: The “+++” escape sequence can be used to
abort the data block transmission and return the
modem to AT command mode.
Note3: The +F0 command can be used to resume
SIA protocol communication after a voice listen-in or
V.32bis interruption.
Remarks
AN93
225
Related parts for SI2415-D-FS
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
SOIC 16/C°/14.4 KBPS ISOMODEM 16-PIN SYSTEM-SIDE - LEAD-FREE
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
TSSOP 24/I°/14.4 KBPS ISOMODEM SYSTEM-SIDE
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
IC ISOMODEM W/DAA 16SOIC
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM W/DAA 24TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
Telecom Line Management ICs
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
Modem Chip Chipset 56Kbps 24-Pin TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM SYSTEM-SIDE 24TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
SMD/C°/SINGLE-ENDED OUTPUT SILICON OSCILLATOR
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
N/A N/A/SI4010 AES KEYFOB DEMO WITH LCD RX
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
N/A N/A/SI4010 SIMPLIFIED KEY FOB DEMO WITH LED RX
Manufacturer:
Silicon Laboratories Inc
Datasheet: