FTP-621DCL003 Fujitsu Components, FTP-621DCL003 Datasheet
FTP-621DCL003
Specifications of FTP-621DCL003
FTP-621DCL003 Summary of contents
Page 1
... DRIVE INTERFACE BOARD FTP-621DCL003/013 FOR FTP-621/631/641MCL201/202/351/35 n INTERFACE 1. Centronics standard (1) Connector (CN10) Connector part number : FCN-605Q030-G/M (Fujitsu Components) or equivalent Mating connector part number : FCN-607B030-G/B (Fujitsu Components) or equivalent (2) Connector pin assignment No. Signal I/O 1 PRSTB I Data strobe 3 PRDT0 I Data 0 5 PRDT1 I Data 1 7 PRDT2 I Data 2 9 PRDT3 I Data 3 11 PRDT4 I Data 4 ...
Page 2
... Connector pin number Components) FCN-605Q030-G/M (Fujitsu equivalent FTP-621DCL003/013 (4) Data input signal timing or 2 ...
Page 3
... AB18 O External address bus 18 35 AB20 O External address bus 20 37 AB22 O External address bus 22 39 RAM2 O Common RAM access Notes: • Symbol “— —” means a negative logic signal. • “I” or “O” means a signal direction from the interface board side. FTP-621DCL003/013 No. Signal I/O Contents 2 BRD — Data read 4 READY — Data access ready 6 HRQ — User hold request input 8 CLK ...
Page 4
... Mating connector part number : XHP-8 (J.S.T) or equivalent → Cable side No. Signal I/O Contents 1 V — Power supply for head/motor (+24V — Power supply for head/motor (+24V GND — Head/motor ground 7 GND — Head/motor ground FTP-621DCL003/013 No. Signal I/O Contents 2 GND — Logic ground 4 V — Power supply for head/motor (+24V) DD No. Signal I/O Contents 2 V — Power supply for head/motor (+24V) DD ...
Page 5
... Connector for head-up/paper-out detection (CN4) Part number : B5B-XH-A-WHITE (J.S.T) or equivalent → P.C.B side Mating connector part number : XHP-5 (J.S.T) or equivalent → Cable side No. Signal I/O Contents 1 V — Power supply for logic (+5V GND — Logic ground 5 HUP I Head-up detection FTP-621DCL003/013 No. Signal I/O Contents Temperature detection REF 4 ENB1 O Printing enable 1 6 ENB3 O Printing enable 3 8 LAT O Printing data latch No. ...
Page 6
... TMPER O Abnormal head temperature detection 3 GND — Logic ground Note: This signal detects the abnormal head temperature at hardware. 8. Connector for cutter drive (CN6)* Part number: B4B-EH (J.S.T) or equivalent → P.C.B side No. Signal I/O Contents 1 SW1 I Cutter position detection Motor drive (+) *1 Only for FTP-621DCL013 FTP-621DCL003/013 No. Signal I/O 2 NES I Paper near end detection No. Signal I/O 2 N.C. — Not connected 4 MT/A O Stepping motor coil excitation 6 MT/B O Stepping motor coil excitation No. ...
Page 7
... Double width print set Double width print reset Page length set in character line Reverse print set Reverse print reset Bit image print set* Double width print set and reset Printing speed set Line feed length set in n/203 in. Character set 2 select Character set 1 select Download character register Registered download character select Character set copy Bit image print set in high speed* International character set Printer reset Line feed length set after mark detection ESC w+n Mark detection FTP-621DCL003/013 Command LF Prints buffer data and returns the line to left end of next line. FF Prints buffer data and returns the line to left end of next form. CR Prints buffer data and returns the line to left end of next line. SO Sets the double width character. SI Resets the double width character. RS Sets the black-white negative printing. US Resets the black-white negative printing. ...
Page 8
... Paper feed set in normal direction Paper feed set in reverse direction Left-end print position set Right-end print position set FS sequence set 4 times enlarged character set and reset Double height print set and reset Detecting function set TOF mark detection Printing quality set 1 Cutting* Cutting type select Only for FTP-621DCL013 FTP-621DCL003/013 Command ESC J+n Sets the paper feed in normal direction. (Feeding range 255 dot lines) ESC j+n Sets the paper feed in reverse direction. (Feeding range 255 dot lines) ESC l+n Sets the left end of printing position. ESC Q+n Sets the left end of printing position. FS Indicates the start sequence formed by this code plus subsequent commands. Sets and resets the 4 times enlarged characters. ...
Page 9
... Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. August 14, 2007 FTP-621DCL003/013 Part number Cable length FTP-621Y001 150 mm (5.9 inch) FTP-621Y002 150 mm (5 ...