316C TPI (Test Products Int), 316C Datasheet - Page 5

• Manufacturer Part Number: 316C
• Description: PKT DIGITAL THERM W/O MAGNETS
• Manufacturer: TPI (Test Products Int)
• Series: -r
• Type: Pocketr

Specifications of 316C

• Temperature Range: -58 ~ 300°F (-50 ~ 150°C)
• Temperature Display: C°/F°
• Display Type: LCD
• Input Type: Probe
• Features: Auto Off, Hold
• Probe Type: Penetration
• Battery Cell Size: Coin
• Includes: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Copyright © 2008 Test Products International, Inc.
Models 306C Penetration tip comes with A306
Pocket Digital Thermometers
Features and Specifications
* IP rating
Tip Type
Tip Diameter
at Sensor
Stem Length
Field Calibration
Data Hold
°C/°F Switchable
Range
Accuracy
Resolution
Auto Off
Sample Time
Battery
Centigrade versions 306CX
* IP Ratings
Ingress Protection (IP) ratings are developed by the European Committee for Electro Technical Standardization and specify the environmental protection an enclosure
provides.
Definitions for the IP ratings TPI products carry are:
IP61 - Totally protected against dust and against vertically falling drops of water e.g. condensation
IP63 - Totally protected against dust and against direct sprays of water up to 60° from the vertical.
IP65 - Totally protected against dust and against low pressure jets of water from all directions; limited ingress.
IP67 - Totally protected against dust and protected against the effect of immersion between 15cm (6”) and 1m (39”).
FAQ
FEATURES
Pocket Digital Thermometers
How do I check calibration of my
pocket thermometer?
You put the thermometer in a solution
of crushed ice and water, swirl the water
around and it should read close to 32°F.
All “C” version digidials can be
Min. Temp°F
Min. Temp°C
Max. Temp°F
Max. Temp°C
°F
°C
penetration
(127mm)
(3.8mm)
1.5sec
300°F
-40°F
0.1°C
306C
0.15"
1%
63
5”
•
•
•
A306
Protective rubber
boot for the 306C
and 306CX.
www.tpi-thevalueleader.com • 503.520.9197
penetration
(127mm)
(3.1mm)
0.1°F/C
1.5sec
150°C
-50°C
300°F
-58°F
312C
0.12"
±1°C
±2°F
67
5”
•
•
•
•
penetration
(2.9mm)
(71mm)
Does the whole stem need to be
immersed to get an accurate reading?
The sensor is in the tip of the probe
and needs to be 1/2 inch into what you
are measuring.
0.1°F/C
0.115"
1.5sec
300°F
150°C
-58°F
-50°C
316C
±2°F
±1°C
2.8”
67
•
•
•
•
(3.1mm)
(71mm)
0.1°F/C
1.5sec
150°C
chisel
-50°C
300°F
0.12"
±1°C
-58°F
±2°F
2.8”
318
65
•
•
•
All TPI Digital Pocket Thermometers use an LR44 battery
auto field calibrated
Models 312C Penetration-Tip
(71mm)
contact
0.1°F/C
(6mm)
150°C
1.5sec
-50°C
300°F
-58°F
0.24"
±2°F
±1°C
319
2.8”
323
326
65
•
•
•
Chisel-Tip
Needle-Tip
± 1°C (<0 and >70°C)
±2°F (<32 and >158)
± 0.5°C (0 to 70°C)
±1°F (32 to 158°F)
How do I calibrate the “C” version digital thermometer?
1. Insert the stainless steel shaft of the thermometer into an
2. Press and hold the D-H/Cal button for approximately
(1.6mm)
(71mm)
0.1°F/C
needle
1.5sec
150°C
-50°C
300°F
320C
-58°F
0.06"
2.8"
ice water bath and allow the reading to stabilize
8 seconds until “CAL” is displayed. Calibration is complete.
67
•
•
•
•
Models 316C Penetration-Tip
in 32º F ice water to ± 2º F
(125mm)
(3.1mm)
0.1°F/C
150°C
1.5sec
chisel
-50°C
300°F
-58°F
0.12"
±1°C
±2°F
4.9”
323
67
•
•
•
318
319
320C Small diameter
329
330C Chisel-Tip
(125mm)
(1.6mm)
0.1°F/C
needle
150°C
1.5sec
Chisel-Tip
Contact-Tip
tapered penetration-Tip
Contact-Tip
( no protective sheath )
-50°C
300°F
-58°F
±2°F
±1°C
0.06
326
4.9”
67
•
•
•
(125mm)
0.1°F/C
contact
(6mm)
288°C
1.5sec
-50°C
550°F
0.24”
-58°F
±1°C
±2°F
4.9”
329
65
•
•
•
(Photo)
(0.06” in 1.6mm)
(125mm)
(3.1mm)
0.1°F/C
1.5sec
-50°C
550°F
288°C
chisel
-58°F
330C
0.12”
±2°F
±1°C
4.9”
67
•
•
•
•
5