HI-6010CT Holt Integrated Circuits, HI-6010CT Datasheet
HI-6010CT
Specifications of HI-6010CT
Related parts for HI-6010CT
HI-6010CT Summary of contents
Page 1
... Error flags are generated for transmitter underwrites and for receiver data framing miscues, parity errors, and buffer overwrites. The HI-6010 volt chip that will require data transla- tion from and to the ARINC bus. The HI-8482 and HI-8588 line receivers are available for the receiver side and the HI-318X and HI-858X line drivers are available for the transmitter side ...
Page 2
... HI-6010 DESCRIPTION 0.0 Volts Error indication if high. Status register must be read to determine specific error. Enables data transmission when low. Source clock for data transmission. 4 times bit rate. Hardware feature select. Master reset, active high. ...
Page 3
... This pin must have a clock applied that is 4X the desired receive frequency. PIN 13 - FCR In 8 bit mode, this pin flags the first character (byte) received bit mode, this pin goes high for a valid 32 bit word. The pin is not affected by CR3 programming. HI-6010 PIN 14 - RXD0 and PIN 16 - RXD1 These pins must be 5 volt logic levels ...
Page 4
... PIN 10 - TXD0 and PIN 11 - TXD1 TXD0 will go high during a transmission if the data is zero. TXD1 goes high if data is a one. When both pins are low this is referred to as the Null state. transmitter chip, such as the HI-3182, HI-3183, HI-8585 or HI-8586 is connected to these pins to translate the 5 volt levels to the proper ARINC bus levels ...
Page 5
... With Pin 5 low, Control Register Bit 5 selects if the 32nd bit is either odd parity or data Pulse P = Pulse X = Don't Care X = Don't Care HI-6010 Load Control Word TXRDY & TXE Go Low After Load Data TD3 TD2 TD1 Monitor Pin High After Pin 9 High Then Load Next Byte Monitor Pin High Load Monitor Pin High Load Transmission Complete ...
Page 6
... Read 2nd Byte Read 3rd Byte Read 4th Byte Write CR Monitor the Status Register & High - First Character Read 1st Byte RD3 RD2 RD1 Look for High Again Read 2nd Byte Look for High Again Read 3rd Byte Look for High Again ...
Page 7
... TD24 TD23 TD22 TD21 TD20 TD19 TD18 TD17 D31 TD30 TD29 TD28 TD27 TD26 TD25 Pulse P = Pulse X = Don't Care X = Don't Care HI-6010 Load Control Word & Load Data to Transmit - Byte 1 TD3 TD2 TD1 Load Data to Transmit - Byte Load Data to Transmit - Byte 3 ...
Page 8
... 7L7 7L6 7L5 7L4 7L3 8L7 8L6 8L5 8L4 8L3 P = Pulse P = Pulse X = Don't Care X = Don't Care HI-6010 LOADING LABELS Control Bit 7 Must Be 0 First Write 1 into Control Bit 7 1L2 1L1 1L0 Load the 1st Label ...
Page 9
... C/D t CDS DATA VALID BUS t CSSR CS Figure 1. TRANSMTTER OPERATION CTS t CTL t CPW TXE t ENDAT TXD0/ FIRST TXD1 BIT TXRDY Figure 3. HI-6010 DATA BUS TIMING - WRITE C/D t CDH DATA BUS t CSHR CS t DTX LAST t BIT TXRY HOLT INTEGRATED CIRCUITS 9 VALID CDH CDS WP ...
Page 10
... CTL t ENDAT t TXRDY t TDTX t CPW HOLT INTEGRATED CIRCUITS 10 P 500mW D T (Industrial) -40°C to +85° (Hi temp & Military) -55°C to +125° -65°C to +150°C STG T 300°C for 60 Seconds LEAD MIN TYP MAX UNITS 4.75 5 5.25 V 2.1 1.4 V 1.4 0.7 V 1.5 µ ...
Page 11
... ORDERING INFORMATION HI - 6010C x-xx PART NUMBER Blank T M-01 PART NUMBER 6010C HI - 6010J x x PART NUMBER Blank F PART NUMBER Blank T PART NUMBER 6010J HI-6010 TEMPERATURE BURN RANGE FLOW IN -40°C TO +85° -55°C TO +125° -55°C TO +125°C M Yes PACKAGE DESCRIPTION 28 PIN CERAMIC SIDE BRAZED DIP (28C) ...
Page 12
... SQ. .173 ±.008 (4.394 ±.203) BSC = “Basic Spacing between Centers” is theoretical true position dimension and has no tolerance. (JEDEC Standard 95) HI-6010 PACKAGE DIMENSIONS 1.400 ±.014 (35.560 ±.356) .595 ±.010 (15.113 ±.254) .050 typ (1.270) .085 ± ...