ISL54210IRTZ Intersil, ISL54210IRTZ Datasheet - Page 11

• Manufacturer Part Number: ISL54210IRTZ
• Description: IC SWITCH DUAL SPDT HS 10-TDFN
• Manufacturer: Intersil

Specifications of ISL54210IRTZ

• Function: Switch
• Circuit: 2 x SPDT
• Voltage Supply Source: Single Supply
• Voltage - Supply, Single/dual (±): 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-TDFN Exposed Pad
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Typical Application Block Diagram
Detailed Description
The ISL54210 device is a dual single pole/double throw
(SPDT) analog switch that operates from a single DC
power supply in the range of 2.7V to 3.6V. It was
designed to function as a dual 2-to-1 multiplexer to
select between USB differential data signals and audio L
and R stereo signals. It comes in tiny µTQFN and TDFN
packages for use in MP3 players, PDAs, cellphones, and
other personal media players.
The part consists of two 2.5Ω audio switches and two
5.5Ω USB switches. The audio switches can accept
signals that swing below ground. They were designed to
pass audio left and right stereo signals, that are ground
referenced, with minimal distortion. The USB switches
were designed to pass high-speed USB differential data
signals with minimal edge and phase distortion.
The ISL54210 was specifically designed for MP3 players,
personal media players and cellphone applications that
need to combine the audio headphone jack and the USB
data connector into a single shared connector, thereby
saving space and component cost. A “Typical Application
Block Diagram” of this functionality is shown on page 11.
The ISL54210 incorporates circuitry for the detection of
the USB V
the audio CODEC drivers and USB transceiver of the MP3
player or cellphone. The ISL54210 contains a logic
control pin (CTRL) that when driven low while V
low, opens all switches and activates the audio click and
pop circuitry.
A detailed description of the two types of switches are
provided in the following sections. In a typical
application, the USB transmission and audio playback are
intended to be mutually exclusive operations.
BUS
voltage, which is used to switch between
V
BUS
11
COM -
COM +
V
BUS
4MΩ
200kΩ
200kΩ
LOGIC CONTROL
BUS
3.3V
GND
ISL54210
ISL54210
is
V
DD
CLICK
AND
POP
Audio Switches
The two audio switches (L, R) are 2.5Ω switches that can
pass signals that swing below ground. Crosstalk between
the audio switches is <-100dB over the audio band.
These switches have excellent off-isolation >105dB over
the audio band with a 32Ω load.
Over a signal range of
V
resistance variation. They can pass ground referenced
audio signals with very low distortion (<0.06% THD+N)
when delivering 15.6mW into a 32Ω headphone speaker
load. See Figures 16, 17, 18, and 19 THD+N in “Typical
Performance Curves” beginning on page 14.
The audio drivers should be connected at the L and R
side of the switch (pins 5 and 6 for µTQFN, pins 6 and 7
for TDFN) and the speaker loads should be connected at
the COM side of the switch (pins 2 and 3 for µTQFN, pins
3 and 4 for TDFN).
The audio switches have click and pop circuitry on the L
and R side that is activated when the V
V
floating. The ISL54210 should be put in this mode before
powering down or powering up of the audio CODEC
drivers. In this mode, both the audio and USB in-line
switches will be OFF and the audio click and pop circuitry
will be ON. The high off-isolation of the audio switches
along with the click and pop circuitry will isolate the
transients generated during power-up and power-down
of the audio CODECs from getting through to the
headphones, thus eliminating click and pop noise in the
headphones.
The audio switches are active (turned ON) whenever the
V
voltage
DD
DD
BUS
> 2.7V, these switches have an extremely low r
+ 0.2V or floating and the CTRL voltage
4MΩ
CTRL
voltage is
≥
to 1.4V.
D-
D+
R
L
≤
V
DD
±
+ 0.2V or floating and the CTRL
1V (0.707V
µCONTROLLER
TRANSCEIVER
HIGH-SPEED
CODEC
AUDIO
USB
RMS
BUS
) with
voltage is
≤
March 18, 2010
to 0.5V or
FN6661.2
ON
≤